Cisco NCS 2000 series Скачать руководство пользователя страница 515 | Manualshive

Страница: 515 / 602

background image

Transient Conditions

This section lists in alphabetical order all the transient conditions encountered in Software Release 9.1. The
description, entity, SNMP number, and SNMP trap accompany each condition.

ADMIN-DISABLE

The Disable Inactive User (ADMIN-DISABLE) condition occurs when the administrator disables a user or
when a account is inactive for a specified period.

This transient condition does not result in a standing condition.

ADMIN-DISABLE-CLR

The Disable Inactive Clear (ADMIN-DISABLE-CLR) condition occurs when the administrator clears the
disable flag on a user account.

This transient condition does not result in a standing condition.

ADMIN-LOCKOUT

The Admin Lockout of User (ADMIN-LOCKOUT) condition occurs when the administrator locks a user
account.

This transient condition does not result in a standing condition.

ADMIN-LOCKOUT-CLR

The Admin Lockout Clear (ADMIN-LOCKOUT-CLR) condition occurs when the administrator unlocks a
user account or when the lockout time expires.

This transient condition does not result in a standing condition.

ADMIN-LOGOUT

The Admin Logout of User (ADMIN-LOGOUT) condition occurs when the administrator logs off a user
session.

This transient condition does not result in a standing condition.

ADMIN-SUSPEND

The Suspend User (ADMIN-SUSPEND) condition occurs when the password for a user account expires.

This transient condition does not result in a standing condition.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

469

Transient Conditions

Transient Conditions

«
...
513
514
515
516
517
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 31

Бренд: Samsung Страницы: 15

Бренд: CAME Страницы: 19

Бренд: Ebyte Страницы: 8

Бренд: JCG Страницы: 2

Бренд: Magma Страницы: 2

Бренд: Magnadyne Страницы: 13

Бренд: Raritan Страницы: 4

Бренд: Ubiquiti Страницы: 50

Бренд: Alacritech Страницы: 20

Sure Cross DX70

Бренд: Banner Страницы: 35

Бренд: Lanner Страницы: 109

AXP-100H MUSCLE

Бренд: Thermalright Страницы: 36

Бренд: Magnadyne Страницы: 8

kontron KBox E-420-R1K/V1K

Бренд: S&T Страницы: 82

LinkStation Mini

Бренд: Buffalo Страницы: 71

Бренд: Eaton Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды