Cisco NCS 2000 series Скачать руководство пользователя страница 484 | Manualshive

Страница: 484 / 602

background image

• OCH-circuit associated to the port is deleted or set to OOS state.

• Hardware reset or card removal.

• Software reset of the card.

Although the WVL-DRIFT-CHAN-OFF condition is raised in the optical card, make sure that the laser source
connected to the MSTP equipment is investigated to isolate the origin of the issue. Laser is likely affected by
wavelength instability or wavelength drift causing this condition to occur.

Note

WVL-MISMATCH

Default Severity: Major (MJ), Service-Affecting (SA)

Logical Object: TRUNK

The Equipment Wavelength Mismatch alarm applies to the following cards: TXP_MR_2.5G, TXPP_MR_2.5G,
TXP_MR_10E, TXP_MR_10E_C, TXP_MR_10E_L, MXP_2.5G_10G, MXP_2.5G_10E, MXP_2.5G_10E_C,
MXP_2.5G_10E_L, MXP_MR_2.5G, MXPP_MR_2.5G, MXP_MR_10DME_C, MXPP_MR_10DME_C,
AR_MXP, AR_XP, AR_XPE, ADM-10G, and OTU2_XP cards. It occurs when you provision the card in
CTC with a wavelength that the card does not support.

For more information about supported card wavelengths, refer to the

Hardware Specifications

document.

Note

Clear the WVL-MISMATCH alarm

SUMMARY STEPS

1.

In node view (single-shelf mode) or shelf view (multishelf mode), double-click the TXP or MXP card to
open the card view.

2.

Click the

Provisioning

>

Line

>

Wavelength Trunk Provisioning

tabs.

3.

In the Wavelength field, view the provisioned card wavelength.

4.

If you have access to the site, compare the wavelength listed on the card faceplate with the provisioned
wavelength. If you are remote, compare this wavelength with the card identification in the inventory:

5.

If the card was provisioned for the wrong wavelength, double-click the card in node view (single-shelf
mode) or shelf view (multishelf mode) to open the card view.

6.

Click the

Provisioning

>

Line

>

Wavelength Trunk Provisioning

tabs.

7.

In the Wavelength field, click the drop-down list and choose the correct wavelength.

8.

Click

Apply

.

DETAILED STEPS

Step 1

In node view (single-shelf mode) or shelf view (multishelf mode), double-click the TXP or MXP card to open the card
view.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

438

Alarm Troubleshooting

WVL-MISMATCH

«
...
482
483
484
485
486
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

S5500-HI Switch Series

Бренд: H3C Страницы: 180

Бренд: H3C Страницы: 84

Бренд: H3C Страницы: 281

Бренд: H3C Страницы: 8

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 33

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 102

S12500CR Series

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 15

H3C S7500E Series

Бренд: H3C Страницы: 1565

Бренд: H3C Страницы: 4

Patton SmartNode 2300 Series

Бренд: Patton electronics Страницы: 2

Бренд: Paradyne Страницы: 12

Transportation FiberinMotion

Бренд: Radwin Страницы: 122

Бренд: Datasat Страницы: 170

Бренд: Watchguard Страницы: 40

Wisenet PRN-6400B4

Бренд: Hanwha Techwin Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды