Cisco NCS 2000 series Скачать руководство пользователя страница 591 | Manualshive

Страница: 591 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

Refer to the error message text.

The data cannot be retrieved because ANS parameters
cannot be calculated on the node in its current
configuration.

EID-6252

Refer to the error message text.

Invalid Margin For Span Aging.

EID-6253

Timing reference is not supported by
SDH mode.

SDH mode does not support timing references.

EID-6254

Refer to the error message text.

Only DS1 interfaces with ESF line types support timing
references.

EID-6255

Refer to the error message text.

sendDoNotUse and sendDoNotUseFF are mutually
exclusive.

EID-6256

Refer to the error message text.

The termination is already in use.

EID-6257

Refer to the error message text.

The side is carrying services or traffic.

EID-6258

Refer to the error message text.

A pluggable module on Port 22 remains unmanaged.

EID-6259

Refer to the error message text.

You cannot delete this port. There was a severe
architectural error related to the index of the pluggable
trunk port object. Please contact technical support for
assistance.

EID-6260

The user adds a row without a valid
VLAN database loaded.

This is not a valid VLAN ID. The VLAN database is
empty.

EID-6261

The user provisions a double footprint
card in a single slot.

The equipment requires two slots.

EID-6263

Refer to the error message text.

The patchcord is duplicated.

EID-6264

Refer to the error message text.

The wavelength is in use by an OCH trail, a virtual link,
or an internal patchcord.

EID-6265

Refer to the error message text.

The card cannot be changed because the port has not
been provisioned.

EID-6266

Refer to the error message text.

Each port can have a maximum of 8 MAC addresses.

EID-6267

Refer to the error message text.

This server trail does not have a valid start or end.

EID-6268

Refer to the error message text.

The maximum number of server trails is 3743.

EID-6269

Refer to the error message text.

A unique server trail ID could not be allocated.

EID-6270

Refer to the error message text.

The server trail already exists.

EID-6271

Refer to the error message text.

The server trail size must not exceed the port
bandwidth.

EID-6272

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

545

Error Messages

Error Messages Reference

«
...
589
590
591
592
593
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

DES-3526 - Switch - Stackable

Бренд: D-Link Страницы: 258

Бренд: Patton electronics Страницы: 2

Бренд: Linksys Страницы: 2

Ray 3 Plus Client

Бренд: Sun Microsystems Страницы: 6

Бренд: Lab.gruppen Страницы: 35

Patton SmartNode 2300 Series

Бренд: Patton electronics Страницы: 2

Бренд: Paradyne Страницы: 12

SCSI PC Card REX-9530V

Бренд: Ratoc Systems Страницы: 30

Бренд: Allnet Страницы: 12

Бренд: Telebyte Страницы: 19

Бренд: Dantel Страницы: 62

Storage Networking (Unified Fabric Pilot)

Бренд: Qlogic Страницы: 76

Бренд: C-Smartlink Страницы: 7

OMB-DAQBOARD-500 Series

Бренд: Omega Страницы: 48

Бренд: Hunter Страницы: 2

Бренд: Chase Research Страницы: 114

Бренд: SilverStone Страницы: 28

Бренд: Fluke Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды