Cisco NCS 2000 series Скачать руководство пользователя страница 444 | Manualshive

Страница: 444 / 602

background image

a) In node view (single-shelf mode) or shelf view (multishelf mode), for the system serving as the proxy, click the

Provisioning

>

General

>

General

tabs.

b) Ensure that theUse NTP/SNTP Server check box is checked.
c) If the Use NTP/SNTP Server check box is not checked, click it.
d) Ensure that the Use NTP/SNTP Server field contains a valid IP address for the server.

Step 4

If proxy is correctly provisioned, refer to the Timing chapter in the Configuration guide for more information on SNTP
Host.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

SOFT-VERIF-FAIL

Default Severity: Critical (CR), Service-Affecting (SA)

Logical Object: EQPT

The Software Signature Verification Failed (SOFT-VERIF-FAIL) alarm occurs under the following conditions:

• The software running on any line card in the system is tampered with or the software running on the

system did not originate from Cisco.

• Problem present in the software stored in the line cards.

Clear the SOFT-VERIF-FAIL Alarm

SUMMARY STEPS

1.

To clear the alarm, log into the Technical Support Website at

http://www.cisco.com/cisco/web/support/

for more information or call Cisco TAC (1 800 553-2447).

DETAILED STEPS

To clear the alarm, log into the Technical Support Website at

http://www.cisco.com/cisco/web/support/index.html

for

more information or call Cisco TAC (1 800 553-2447).

SPANLEN-OUT-OF-RANGE

Default Severity: Minor (MN), Non-Service-Affecting (NSA)

Logical Object: OTS

The SPANLEN-OUT-OF-RANGE alarm is raised when span loss measured by CTC is higher than the
maximum expected span loss (or lower than the minimum expected span loss).

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

398

Alarm Troubleshooting

SOFT-VERIF-FAIL

«
...
442
443
444
445
446
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Rain Bird Страницы: 17

Бренд: Raritan Страницы: 4

Бренд: 3Com Страницы: 16

SuperServer 5019S-L

Бренд: Supermicro Страницы: 61

Бренд: Time domain Страницы: 64

Elite Controller

Бренд: RANA Systems Страницы: 328

Бренд: Abit Страницы: 22

Suzie-Q 541.35.520

Бренд: Hafele Страницы: 12

Бренд: Keil Страницы: 68

Бренд: Intel Страницы: 20

Бренд: ICOP Technology Страницы: 42

N-FXE 02B Series

Бренд: Lantronix Страницы: 10

Бренд: Cypress Semiconductor Страницы: 38

Бренд: Flexwatch Страницы: 13

Бренд: Kordis Страницы: 31

Бренд: Camozzi Страницы: 22

Sporlan Division SCS-PB Series

Бренд: Parker Страницы: 10

Бренд: Grundfos Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды