Cisco NCS 2000 series Скачать руководство пользователя страница 556 | Manualshive

Страница: 556 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

CTC is being launched with the wrong
version of the JRE {0}. This version
of CTC requires a particular version
of the JRE {1}. The CTC and browser
must be closed and restarted to allow
the correct Java version to be loaded.

You are using Java version {0}. CTC should run with
Java version {1}. It can be obtained from the installation
CD or http://java.sun.com/j2se/

WID-3263

Protection Group could not be
modified.

An error occurred while modifying the protection group.

EID-3265

Refer to the error message text.

Conditions could not be retrieved from the shelf or card
view.

EID-3266

Refer to the warning message text.

The XTC protection group cannot be modified.

WID-3267

The specified entry is invalid.

The filter entry is invalid. {0}

WID-3268

Refer to the error message text.

The {0} operation was successfully initiated for {1}
but its completion status could not be obtained from
the node. When the node is accessible, check its
software version to verify if the {0} succeeded.

WID-3269

The specified file does not exist.

The file {0} does not exist.

WID-3270

The value entered must be greater than
the specified value.

The value entered must be greater than {0}.

WID-3271

An entry is required to complete this
task.

An entry is required.

WID-3272

The specified item already exists in
the list.

{0} already exists in the list.

WID-3273

Refer to the warning message text.

A software upgrade is in progress. Network
configuration changes that result in a node reboot
cannot take place during a software upgrade. Please try
again after the software upgrade is done.

WID-3274

Refer to the warning message text.

Ensure that the remote interface ID and the local
interface ID on the two sides match. (The local interface
ID on this node should equal the remote interface ID
on the neighbor node and vice-versa).

WID-3275

The specified port has both SDCC and
LDCC.

Both {0} and {1} exist on the same selected port. {2}

WID-3276

The input exceeds the character limit.
The value will be truncated to the
maximum character limit.

The description cannot exceed {0} characters. Your
input will be truncated.

WID-3277

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

510

Error Messages

Error Messages Reference

«
...
554
555
556
557
558
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Watchguard Страницы: 24

Бренд: Qlogic Страницы: 2

Бренд: TP-Link Страницы: 2

Low Power Series

Бренд: FabiaTech Страницы: 77

Бренд: Cowfish Technologies Страницы: 38

Бренд: Infoblox Страницы: 13

Бренд: Nakayo Страницы: 119

NOVA300 AML02304U1

Бренд: Nexxt Страницы: 75

RanaSystems 13-0010--001

Бренд: RANA Systems Страницы: 328

Бренд: SYNTEK Страницы: 41

Бренд: ANEP Страницы: 48

Бренд: JETWAY Страницы: 47

Бренд: Acromag Страницы: 35

Бренд: Zhone Страницы: 53

Бренд: Paradyne Страницы: 108

Бренд: Draytek Страницы: 17

Бренд: Zonet Страницы: 1

Бренд: Tripp Lite Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды