Cisco NCS 2000 series Скачать руководство пользователя страница 561 | Manualshive

Страница: 561 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

Create an optical linkmodel for the
interface, and proceed.

An optical link model does not exist for the specified
interface.

EID-3358

Refer to the error message text.

Optical parameters could not be set for the node.

EID-3359

Refer to the error message text.

ANS cannot be performed. Please check {0} parameter
value.

EID-3360

You cannot delete a ring in use.

The ring termination is in use. An error occurred while
deleting the ring termination.

EID-3361

There was an error while deleting ring
termination.

An error occurred while deleting the ring termination.

EID-3362

You must select a ring termination.

No ring terminations were selected.

EID-3363

There was an error while creating the
ring ID.

An error occurred while creating the ring ID.

EID-3364

Select another optical service channel
(OSC) which is not in use.

The OSC termination is in use.

EID-3365

There was an error deleting the OSC
termination.

The OSC termination could not be deleted.

EID-3366

You must select an optical link.

No optical link was selected.

EID-3370

Refer to the error message text.

An error occurred while calculating the automatic
optical link list.

EID-3371

CTC destroyed an external attempt to
access an optical channel network
connection.

CTC attempted to access an OCHNC connection that
has been destroyed.

EID-3372

Refer to the error message text.

The expected span loss must be set.

EID-3375

Refer to the error message text.

The measured span loss could not be retrieved.

EID-3376

The interface used for the card is
wrong.

The wrong interface was used.

EID-3377

The provisionable patchcord identifier
to the patchcord you are attempting to
provision is already in use by another
patchcord on the origination node.

This is a duplicate origination patchcord identifier.

EID-3378

The provisionable patchcord identifier
to the patchcord you are attempting to
provision is already in use by another
patchcord on the remote node.

This is a duplicate termination patchcord identifier.

EID-3379

Refer to the error message text.

The host cannot be found.

EID-3380

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

515

Error Messages

Error Messages Reference

«
...
559
560
561
562
563
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Cabletron Systems Страницы: 21

Бренд: Idis Страницы: 123

Бренд: Idis Страницы: 29

Бренд: Idis Страницы: 28

DirectIP DR-1304P

Бренд: Idis Страницы: 82

Бренд: iDirect Страницы: 130

8677 - BladeCenter Rack-mountable - Power...

Бренд: IBM Страницы: 126

Scorpio WD2500BPVT

Бренд: Western Digital Страницы: 3

Scorpio WD2500BPVT

Бренд: Western Digital Страницы: 4

DIRECTOR PRO series

Бренд: MF DIGITAL Страницы: 79

Бренд: Advantech Страницы: 36

Бренд: 1&1 Страницы: 32

WNFB-265AXI(BT)

Бренд: Sparklan Страницы: 14

Бренд: C&T Solution Страницы: 129

UM10301 PCA8565

Бренд: NXP Semiconductors Страницы: 54

Бренд: Hauppauge Страницы: 62

Husky HMG-1648EP

Бренд: Ethernet Direct Страницы: 16

Бренд: M-system Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды