Cisco NCS 2000 series Скачать руководство пользователя страница 357 | Manualshive

Страница: 357 / 602

background image

• Mode conversion from ANSI to ETSI.

Clear the NODE-FACTORY-MODE Alarm

Reset to the default setting using 'Rebuild DB' option.

(or)

Restore the database.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

NOT-AUTHENTICATED

Default Severity: Minor (MN), Non-Service-Affecting (NSA)

Logical Object: SYSTEM

The NOT-AUTHENTICATED alarm is raised by CTC (not by the NE) when CTC fails to log into a node.
This alarm only appears in CTC where the login failure occurred. This alarm differs from the

INTRUSION-PSWD , on page 239

alarm, because INTRUSION-PSWD occurs when a user exceeds the login

failures threshold.

The NOT_AUTHENTICATED alarm is also raised, when CTC nodes in the network have R10.6 packages
and earlier and password policy is less than 80 characters.

NOT-AUTHENTICATED is an informational alarm and is resolved when CTC successfully logs into the
node.

Note

OCHNC-BDI

Default Severities: Not Alarmed (NA), Non-Service-Affecting (NSA)

Logical Objects: OTS

The Optical Channel Network Connection (OCHNC) Backward Defect Indication(BDI) alarm is raised when
an OCHNC signal is interrupted along the circuit path and the system is not able to recover it.

Clear the OCHNC-BDI Alarm

This alarm is cleared automatically when the interrupt is rectified and the signal flows properly.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

311

Alarm Troubleshooting

Clear the NODE-FACTORY-MODE Alarm

«
...
355
356
357
358
359
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: D-Link Страницы: 10

Бренд: NEC Страницы: 47

Бренд: Data Translation Страницы: 60

Бренд: LaCie Страницы: 4

Бренд: LaCie Страницы: 4

Бренд: AMD Страницы: 20

Бренд: Sangamo Страницы: 2

Бренд: ebm-papst Страницы: 11

Бренд: YASKAWA Страницы: 15

Бренд: DAD Страницы: 16

Бренд: Addonics Technologies Страницы: 1

Бренд: Supermicro Страницы: 27

Converter Board R0E521237CFK00

Бренд: Renesas Страницы: 6

BROADCAST POLLING FRAD BPF-14 BU

Бренд: DCB Страницы: 28

Бренд: B&B Electronics Страницы: 17

Бренд: Acromag Страницы: 23

Бренд: Top Страницы: 21

Бренд: Logicube Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды