Cisco NCS 2000 series Скачать руководство пользователя страница 564 | Manualshive

Страница: 564 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

Refer to the warning message text.

CAUTION: Reverting to an earlier software release
may result in TRAFFIC LOSS and loss of connectivity
to the node. It may require onsite provisioning to
recover. If the node was running {0} before, reverting
will restore the {0} provisioning, losing any later
provisioning. If the node was running some other
version, reverting will LOSE ALL PROVISIONING.
{1} {2}

WID-4002

The card may not be an IOS-based
card or it may be rebooting.

The Cisco IOS console is disabled for the card in Slot
{0}.

EID-4003

CTC encountered an error while
cancelling the software upgrade.

An error occurred while canceling the software upgrade.

EID-4004

CTC encountered the specified error
during database backup.

{0} encountered while performing a database backup.

EID-4005

Refer to error message.

The file {0} does not exist or cannot be read.

EID-4006

The size of the file that is being
backed up or restored is zero.

The size of the file {0} is zero.

EID-4007

The specified action cannot be
performed during a software upgrade.
You must try after the upgrade process
is completed.

A software upgrade is in progress. {0} cannot proceed
during a software upgrade. Please try again after the
software upgrade has completed.

WID-4008

CTC encountered the specified error
while restoring the database.

{0} encountered while restoring the database.

EID-4009

Refer to the error message text.

The operation was terminated because: {0}

EID-4010

Refer to the error message text.

An error occurred during provisioning: {0}

EID-4011

Refer to the warning message text.

Node management for {0} is not provided.

WID-4012

Refer to the error message text.

CAUTION: Reverting to an earlier software release
may result in TRAFFIC LOSS and loss of connectivity
to the node. It may requireonsite provisioning to
recover. If the node was running {0} before, reverting
will restore the {0} provisioning, losing any later
provisioning. If the node was running some other
version, reverting will LOSE ALL PROVISIONING.
{1} {2} {3}

EID-4013

The path trace mode does not support
strings that consist of null characters.
You must either change the expected
string or the path trace mode.

The manual path trace mode for this equipment does
not support an expected string consisting of all null
characters. Please change the expected string or the
path trace mode.

EID-4014

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

518

Error Messages

Error Messages Reference

«
...
562
563
564
565
566
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: LaCie Страницы: 44

LaCie Ethernet Disk

Бренд: LaCie Страницы: 2

SATA II ExpressCard 34

Бренд: LaCie Страницы: 2

12big Rack Fibre 8

Бренд: LaCie Страницы: 9

SMART NODE 4950-NCE

Бренд: Patton electronics Страницы: 8

NetLink 2960 RAS

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 2

Бренд: Idis Страницы: 86

Бренд: Paradyne Страницы: 20

Бренд: Paradyne Страницы: 2

Бренд: ?omtime Страницы: 62

TotalStorage SAN16M-R SAN

Бренд: IBM Страницы: 116

Бренд: National Instruments Страницы: 9

TOWERCHRON DP72

Бренд: Grasslin Страницы: 2

Бренд: U.S. Products Страницы: 80

Бренд: RAIDAGE Страницы: 60

Бренд: Netis Страницы: 16

Бренд: Idis Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды