Cisco NCS 2000 series Скачать руководство пользователя страница 261 | Manualshive

Страница: 261 / 602

background image

Step 2

For the TRUNK-RX port, double-click the card and click the

Performance

>

OTN PM

>

FEC PM

tabs. If post-FEC

errors are present, troubleshoot this problem first. If not, move to next step.

Step 3

Verify the status of far-end TXP/MXP connected to the faulty near-end card. Look for any alarms reported by the Client-Rx
port of far-end card. If these alarms exist, troubleshoot them.

If the alarm does not get cleared, you need to report a Service-Affecting (SA) problem. Log into the Technical Support
Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or log into

http://www.cisco.com/c/

en/us/support/web/tsd-cisco-worldwide-contacts.html

to obtain a directory of toll-free Technical Support numbers for

your country.

GFP-CSF-SIGLOSS

Default Severity: Major (MJ), Service-Affecting (SA)

Logical Object: GFP-FAC

The GFP Client Signal Fail due to Sigloss is a secondary alarm raised on local GFP data ports when a remote
Service-Affecting (SA) alarm causes invalid data transmission. The alarm is raised locally on AR_MXP and
AR_XP GFP data ports and does not indicate that a Service-Affecting (SA) failure is occurring at the local
site, but that a SIGLOSS alarm caused by an event is affecting a remote data port's transmission capability.

Clear the GFP-CSF-SIGLOSS Alarm

SUMMARY STEPS

1.

Clear the Service-Affecting (SA) alarm at the remote data port.

DETAILED STEPS

Clear the Service-Affecting (SA) alarm at the remote data port.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

GFP-CSF-SYNCLOSS

Default Severity: Major (MJ), Service-Affecting (SA)

Logical Object: GFP-FAC

The GFP Client Signal Fail Due to Syncloss alarm is a secondary alarm raised on local GFP data ports when
a remote Service-Affecting (SA) alarm causes invalid data transmission. The alarm is raised locally on
AR_MXP and AR_XP GFP data ports and does not indicate that a Service-Affecting (SA) failure is occurring
at the local site, but that a SYNCLOSS alarm caused by an event such as a pulled receive cable is affecting
a remote data port's transmission capability.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

215

Alarm Troubleshooting

GFP-CSF-SIGLOSS

«
...
259
260
261
262
263
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Magnat Audio Страницы: 2

Бренд: IBM Страницы: 104

System Storage TS3100

Бренд: IBM Страницы: 375

Бренд: Quick Eagle Networks Страницы: 4

Бренд: H3C Страницы: 21

Бренд: Compaq Страницы: 112

RouterBOARD SXT 5HnD

Бренд: MikroTik Страницы: 2

Бренд: Roland Страницы: 2

Бренд: Realtek Страницы: 30

Бренд: Avolites Страницы: 24

Бренд: ZyXEL Communications Страницы: 485

Бренд: Lucent Technologies Страницы: 20

Бренд: Xenteq Страницы: 16

Бренд: Maxtor Страницы: 2

Бренд: Ubiquiti Страницы: 13

VIGI NVR1004H-4P

Бренд: TP-Link Страницы: 2

Бренд: PairGain Страницы: 80

Бренд: RTS Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды