manualshive.com logo in svg

Cisco NCS 2000 series, Руководство по устранению неисправностей

"Бесплатный Troubleshooting Manual для Cisco NCS 2000 series теперь доступен для скачивания с manualshive.com. Этот manual поможет вам настроить и обслуживать ваш продукт Cisco, обеспечивая стабильную работу сети. Загрузите его бесплатно прямо сейчас и узнайте все секреты работы с Cisco NCS 2000 series."

Поделиться
Скачать
background image

Description

Error/Warning Message

Error/Warning
ID

You may have reached the maximum
number of characters.

The domain name cannot exceed {0} characters.

EID-5011

Refer to the warning message text.

The software load on {0} does not support the addition
of a node to a 1+1 protection group.

WID-5012

The specified port does not support
Bridge and Roll.

{0} does not support the bridge and roll feature. Please
select a different port.

EID-5013

You must for the automatic network
layout to complete before running it
again.

An automatic network layout is already in progress.
Please wait for it to complete before running it again.

EID-5014

You cannot apply the admin state
operation, specified by {0}, to port
count, specified by {1}.

{0} cannot be applied to {1}.

WID-5015

CTC encountered an error while
provisioning the card.

An error occurred while attempting to provision the
{0}. {1}

EID-5016

You may have to remove the BLSR
manually as it was left incomplete.

Provisioning could not be rolled back. The {0} might
be left in an INCOMPLETE state and should be
manually removed.

EID-5017

You cannot add the node {0} of type
{1} to the host node of type {2}. This
prevents you from hosting both
SONET and SDH nodes in the same
session.

{0} is a(n) {1} node and cannot be added to a(n) {2}
network.

EID-5018

The path trace mode does not support
strings that consist of null characters.
You must either change the expected
string or the path trace mode.

The manual path trace mode for this equipment does
not support an expected string consisting of all null
characters. Please change the expected string or the
path trace mode.

EID-5019

Refer to the warning message text.

Software activation is in progress. Provisioning is not
allowed.

EID-5020

Refer to the error message text.

Software activation is in progress. {0} is not allowed.

EID-5021

Refer to the warning message text.

Warning: Ethergroup circuits are stateless (that is,
always in service). The current state selection of {0}
will be ignored.

WID-5022

CTC encountered a network
communication error. Connectivity
between CTC and the NE was
disrupted, either transiently or
permanently.

CTC cannot communicate with the node. The operation
failed.

EID-5023

Refer to the error message text.

The overhead circuit will not be upgraded.

EID-5024

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

521

Error Messages

Error Messages Reference

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Ubiquiti M900 Quick Start Manual preview
M900
Бренд: Ubiquiti Страницы: 24
D-Link DSL-2740B Installation Manual preview
DSL-2740B
Бренд: D-Link Страницы: 10
dixell XT120C Installing And Operating Insructions preview
XT120C
Бренд: dixell Страницы: 4
NEC P401-TMX4D User Manual preview
P401-TMX4D
Бренд: NEC Страницы: 2
Altera Nios II Hardware Development Manual preview
Nios II
Бренд: Altera Страницы: 42
EMS 2000 IDU Series User Manual preview
2000 IDU Series
Бренд: EMS Страницы: 52
Trend Micro IPS Pro-Module-24C-GE-BP-TM Quick Setup Manual preview
IPS Pro-Module-24C-GE-BP-TM
Бренд: Trend Micro Страницы: 3
Kaya Instruments KY-FGK Reference Manual preview
KY-FGK
Бренд: Kaya Instruments Страницы: 48
ADTRAN DUAL Nx56/64 1200142L1# User Manual preview
DUAL Nx56/64 1200142L1#
Бренд: ADTRAN Страницы: 48
Nexxt Amp300 Quick Installation Manual preview
Amp300
Бренд: Nexxt Страницы: 2
DTS XD10P Installation And Operation Manual preview
XD10P
Бренд: DTS Страницы: 94
PairGain HiGain Line Unit HLU-388 Quick Installation Manual preview
HiGain Line Unit HLU-388
Бренд: PairGain Страницы: 7
RuggedCom RuggedSwitch RS500 Installation Manual preview
RuggedSwitch RS500
Бренд: RuggedCom Страницы: 16
MEN ME4 User Manual preview
ME4
Бренд: MEN Страницы: 48
Calix GigaSpire BLAST u4hm Installation Manual preview
GigaSpire BLAST u4hm
Бренд: Calix Страницы: 45
Comnet CNGE28FX4TX24MS2 Installation And Operation Manual preview
CNGE28FX4TX24MS2
Бренд: Comnet Страницы: 154
Moxa Technologies CP-102N-T Quick Installation Manual preview
CP-102N-T
Бренд: Moxa Technologies Страницы: 8
ADTRAN 1202880E1 Quick Start Manual preview
1202880E1
Бренд: ADTRAN Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды