Cisco NCS 2000 series Скачать руководство пользователя страница 409 | Manualshive

Страница: 409 / 602

background image

PROTNA

Default Severity: Minor (MN), Non-Service-Affecting (NSA)

Logical Object: EQPT

The Protection Unit Not Available (PROTNA) alarm is raised when a standby control card is not available.

Clear the PROTNA Alarm

SUMMARY STEPS

1.

Ensure that the standby control card is installed and provisioned in the chassis.

DETAILED STEPS

Ensure that the standby control card is installed and provisioned in the chassis.

PROV-MISMATCH

Default Severity: Minor (MN), Non-Service-Affecting (NSA)

Logical Object: EQPT

The Provisioning Mismatch alarm is raised against a PPM connector on MXP_2.5G_10E, MXP_2.5G_10E_C,
MXP_2.5G_10E_L, MXP_2.5G_10G, MXP_MR_2.5G, MXPP_MR_2.5G, TXP_MR_2.5G, TXP_MR_10E,
TXP_MR_10E_C, TXP_MR_10E_L, TXPP_MR_2.5G, GE_XP, 10GE_XP, ADM-10G, OTU2_XP, MR-MXP,
WSE, 10x10G-LC, 100G-LC-C, 100G-CK-LC, 200G-CK-LC, 100GS-CK-LC, 400G-XP, CFP-LC, AR-XP,
AR-MXP, AR-XPE, 40G-MXP, 40G-TXP, 40E-MXP, and 40E-TXP cards under one of the following
circumstances:

• The physical PPM range or wavelength does not match the provisioned value. PPMs have static wavelength

values which must match the wavelengths provisioned for the card in the case of non-DWDM PPMs.

• The PPM reach (loss) value does not meet the reach value needed for the card.

• The reach of the inserted PPM does not match the physical PPM.

This alarm is raised on GE_XP and 10GE_XP cards, if the following settings are configured:

• Double Add and Translate Add selective modes

• CVLAN Ingress CoS

• MAC address learning on SVLAN

Until this alarm is cleared, provisioning on the GE_XP and 10GE_XP cards is not possible

The Provisioning Mismatch (PROV-MISMATCH) alarm is raised against a TNC/TNCS/TNCE/TNCS-O
card under one of the following circumstances:

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

363

Alarm Troubleshooting

PROTNA

«
...
407
408
409
410
411
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Eaton Страницы: 10

Бренд: LAWO Страницы: 154

Бренд: JB Systems Страницы: 24

Бренд: JB Systems Страницы: 61

Бренд: F5 Страницы: 72

Бренд: Industrex Страницы: 51

Бренд: Compaq Страницы: 112

RouterBOARD SXT 5HnD

Бренд: MikroTik Страницы: 2

Бренд: H3C Страницы: 77

Fieldpoint cFP-RTD-124

Бренд: National Instruments Страницы: 15

SmartMesh IA-510 D2511

Бренд: Dust Networks Страницы: 30

Бренд: Draytek Страницы: 2

Бренд: Genie Страницы: 6

NIC-FC730i-Mb-2-32G

Бренд: H3C Страницы: 37

Бренд: S&T Страницы: 28

Бренд: VideoWave Страницы: 12

Бренд: PairGain Страницы: 80

Бренд: AC Infinity Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды