Cisco NCS 2000 series Скачать руководство пользователя страница 578 | Manualshive

Страница: 578 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

Complete node information could not
be retrieved.

Unable to set the Maintenance state for {0}

EID-5168

Refer to the error message text.

Some routers have responded not to start maintenance.

Do you still want to go ahead with the maintenance
activity?

WID-5169

Refer to the error message text.

Some Transport Admin States cannot be synchronized.

Network operation might be inconsistent.

WID-5170

Refer to the error message text.

Some routers have not responded with Embargo status.

Continuing maintenance activity may be traffic
affecting.

Are you sure you want to continue?

WID-5171

Refer to the error message text.

Provisionable patchcords can not be created between
incompatible ports.

EID-5172

Refer to the error message text.

Some Server Trail terminations were not repaired.

EID-5173

Refer to the error message text.

Routing constraints has been specified only for
protected path.

Can be evaluated to move some constraints on working
path since these are treated with priority.

Please consider that some good constraint on protected
part may not be evaluated correctly since that constraint
may be already applied to working path by auto-routing.

Do you want to continue anyway?

WID-5174

Refer to the error message text.

Unknown Error occurred while updating the SRLG
value on the CRS node(s).

{0}

EID-5175

Refer to the error message text.

One or more SVLANs are invalid.

Please remove them before continuing.

WID-5176

Refer to the error message text.

Unable to trace Layer 2 topology. The root link may
have been deleted.

EID-5190

Clear the proactive protection on the
router manually.

Unable to clear proactive protection on the router. Do
it manually.

WID-5206

Refer to the error message text.

Error in trunk configuration on {0}.

EID-5217

Refer to the error message text.

Gmpls circuits can not be reconfigured.

EID-5218

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

532

Error Messages

Error Messages Reference

«
...
576
577
578
579
580
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Express Ethernetwork DI-704P

Бренд: D-Link Страницы: 17

Бренд: D-Linke Страницы: 32

Бренд: Vanguard Страницы: 121

Бренд: National Instruments Страницы: 5

Бренд: National Instruments Страницы: 76

Бренд: National Instruments Страницы: 34

Бренд: TC Electronic Страницы: 55

Бренд: Alesis Страницы: 61

Fast SwitchHub-8mi SNMP

Бренд: Accton Technology Страницы: 13

Supero SAS-826A

Бренд: Supero Страницы: 16

Бренд: Supermicro Страницы: 16

Бренд: Patton electronics Страницы: 12

Бренд: Watchguard Страницы: 30

Бренд: Speedtouch Страницы: 124

Бренд: Datasat Страницы: 24

Бренд: TP-Link Страницы: 2

IPLink 2603 Series

Бренд: Patton Страницы: 120

Бренд: ACTi Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды