Cisco NCS 2000 series Скачать руководство пользователя страница 596 | Manualshive

Страница: 596 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

Refer to the warning message text.

One or more QinQ rules have not been deleted because
they are not related to the current circuit.

WID-6340

Refer to the warning message text.

The Functional view on {0} is disabled.

WID-6341

Refer to the warning message text.

Changing the {0} settings might be traffic affecting.
Do you want to continue?

WID-6342

Refer to the warning message text.

The selected file name is too long. File names
(including the full path) must be less than 254
characters.Please enter a valid file name.

WID-6343

Refer to the error message text.

It is detected a shelf mismatch condition.

EID-6344

Refer to the error message text.

The line termination is invalid.

EID-6345

Refer to the error message text.

The overhead is not supported.

EID-6346

Refer to the error message text.

A patchcord was expected for a successful operation.

EID-6347

Refer to the error message text.

A Virtual link already exists on the same path.

EID-6348

Refer to the error message text.

The overhead creation has failed.

EID-6349

Refer to the error message text.

The unprotected line is not present

EID-6350

Refer to the error message text.

The port status is active.

EID-6351

Refer to the error message text.

IPv4 access cannot be disabled when IPv6 mode is not
enabled on the node.

EID-6352

Refer to the error message text.

IPv4 access cannot be disabled when the node is in
Multishelf configuration.

EID-6353

Refer to the error message text.

Disabling IPv4 access may lead to loss of
communication with the node. Make the change
anyway?

EID-6354

Refer to the error message text.

IPv6 access cannot b disabled when IPv4 Access is
disabled on the node.

EID-6355

Refer to the error message text.

Multishelf configuration cannot be enabled when IPv4
Access is disabled on the node.

EID-6356

Refer to the error message text.

The Multicast SVLAN field can be modified only when
the MVR feature is disabled.

EID-6357

Refer to the error message text.

Too many TRANSLATE QinQ rules per port with
MVR feature enabled.

EID-6358

Refer to the error message text.

The PLIM {0} is part of an OCH Trail circuit and its
configuration cannot be changed.

EID-6359

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

550

Error Messages

Error Messages Reference

«
...
594
595
596
597
598
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Parker Страницы: 344

Бренд: Paradyne Страницы: 22

Бренд: Cambium Networks Страницы: 29

Бренд: Hama Страницы: 10

S5120V3-EI Series

Бренд: H3C Страницы: 54

Бренд: Ublox Страницы: 116

Бренд: H3C Страницы: 116

Бренд: Axis Страницы: 104

Бренд: Intel Страницы: 108

Бренд: Fortinet Страницы: 20

Бренд: bintec elmeg Страницы: 33

Бренд: iCEBOX Страницы: 57

Бренд: Lanner Страницы: 38

Бренд: Allied Telesis Страницы: 34

Бренд: Wave Wireless Networking Страницы: 167

Бренд: Intel Страницы: 578

Бренд: Planet Страницы: 2

Бренд: Xcellon Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды