Cisco NCS 2000 series Скачать руководство пользователя страница 536

Страница: 536 / 602

Description

Error/Warning Message

Error/Warning
ID

A circuit cannot occupy different STS
regions on different spans. You may
add a different span or delete the
specified circuit.

You cannot add this span. It would cause the following
circuit(s) to occupy different {0} regions on different
spans: {1}

Either select a different span or delete the above
circuit(s).

EID-2127

An internal error occurred while trying
to remove a span from a BLSR.

This alarm occurs in the network-level
BLSR creation dialog box.

The state is invalid.

EID-2128

Refer to the error message text.

You cannot use same slot for east and west protect
ports.

EID-2129

Enter a ring ID value between 0 and
9999.

The ring ID value, {0}, is not valid. Please enter a valid
number between 0 and 9999.

EID-2130

You must select another reversion
type.

The reversion cannot be set to INCONSISTENT.

EID-2131

Input/Output error. Unable to store
overhead circuit preferences.

The overhead circuit preferences could not be stored:
{0}

EID-2135

There was an error while merging the
circuits.

An error occurred during the circuit merge. {0}

EID-2137

Refer to the error message text.

Not all destinations could be deleted. Please try again.

EID-2138

There was an error in updating the
circuit destinations.

An error occurred while updating the destinations.

EID-2139

Select the version of online help, and
proceed.

No online help version was selected. The online help
book cannot be deleted.

EID-2143

You cannot delete the specified online
help.

An error occurred while deleting the online help
book(s). {0}

EID-2144

Refer to error message.

No nodes appear to have a Cisco IOS card.

EID-2145

You cannot logout of an account other
than your own.

This is a security violation. You may only logout of
your own account.

EID-2146

You cannot change an account other
than your own.

This is a security violation. You may only change your
own account.

EID-2147

You cannot delete the account you are
currently logged in.

This is a security violation. You cannot delete the
account under which you are currently logged in.

EID-2148

Refer to the error message text.

There is no exportable content in this view.

WID-2149

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

490

Error Messages

Error Messages Reference

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание NCS 2000 series

Отзывы:

Похожие инструкции для NCS 2000 series

Бренды по названию

Популярные бренды

Cisco NCS 2000 series, Руководство по устранению неисправностей

Результаты поиска

Содержание NCS 2000 series

Отзывы:

Похожие инструкции для NCS 2000 series

Бренды по названию

Популярные бренды