Cisco NCS 2000 series Скачать руководство пользователя страница 533 | Manualshive

Страница: 533 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

You have not selected any profile or
column. Reset operation is done by
right-clicking the selected column.

Select one or more profiles.

EID-2074

A permanent column cannot be reset.

This column is permanent and cannot be reset.

EID-2075

You cannot rename a permanent
column.

This column is permanent and cannot be renamed.

EID-2077

You cannot compare two profiles
unless you select two columns.

At least two columns must be highlighted.

EID-2078

Refer to the error message text.

The alarm types cannot be loaded into table. There are
no reachable nodes from which the list of alarm types
can be loaded. Please wait until such a node is reachable
and try again.

EID-2079

The specified node does not have any
profiles.

The node {0} has no profiles.

EID-2080

There was an error while removing the
specified profile from the specified
node.

An error occurred while removing profile {0} from the
node {1}.

EID-2081

CTC cannot find the specified profile
from the specified node.

The profile {0} does not exist on the node {1}.

EID-2082

There was an error adding the
specified profile to the specified node.

An error occurred while adding profile {0} to the node
{1}.

EID-2083

You tried to select an invalid profile.
Select another profile.

The profile selection is invalid. No profiles were
selected.

EID-2085

You tried to select an invalid node.
Select another node.

The node selection is invalid. No nodes were selected.

EID-2086

Refer to the error message text.

No profiles were selected. Please select at least one
profile.

EID-2087

The profile name cannot be empty.

The profile name is invalid.

EID-2088

Select a unique name.

Too many copies of {0} exist. Please choose another
name.

EID-2089

You must select one or more nodes on
which you can store the profile.

No nodes were selected. Please select the node(s) on
which to store the profile(s).

EID-2090

CTC is unable to switch to the
specified node.

Unable to switch to the node {0}.

EID-2091

CTC encountered a general exception
error while trying to complete the task.

A general exception error occurred.

EID-2092

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

487

Error Messages

Error Messages Reference

«
...
531
532
533
534
535
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Univerge SV8100

Бренд: NEC Страницы: 44

Бренд: D-Link Страницы: 10

Бренд: N-Tron Страницы: 138

Бренд: YASKAWA Страницы: 68

Бренд: NETGEAR Страницы: 169

Бренд: Avolites Страницы: 24

Бренд: ZyXEL Communications Страницы: 485

Бренд: NETGEAR Страницы: 2

PISO-725 Series

Бренд: ICP DAS USA Страницы: 8

NetIron MLXe Series

Бренд: Brocade Communications Systems Страницы: 305

Oresund EFC102200

Бренд: Bridgeworks Страницы: 84

PCard-E 021L-D5 Series

Бренд: ORiNG Страницы: 2

Бренд: Digisol Страницы: 81

Бренд: ZyXEL Communications Страницы: 23

Бренд: Digisol Страницы: 73

Бренд: Intel Страницы: 44

Kontron CP3005 Series

Бренд: S&T Страницы: 115

Бренд: Firetide Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды