Cisco NCS 2000 series Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 602

background image

Solution

The clock is running at the frequency of the last known-good reference input. This alarm is raised

when the last reference input fails. See the

HLDOVRSYNC , on page 226

for a detailed description.

Solution

The NCS supports holdover timing per Telcordia GR-436 when provisioned for external (BITS)

timing.

Note

Free-Running Synchronization Mode

Problem

The clock is running at a different frequency than normal and the

FRNGSYNC , on page 207

appears.

Possible Cause

No reliable reference input is available.

,

Solution

The clock is using the internal oscillator as its only frequency reference. This occurs when no reliable,

prior timing reference is available. See the

FRNGSYNC , on page 207

for a detailed description.

Daisy-Chained BITS Not Functioning

Problem

You are unable to daisy chain the BITS sources.

Possible Cause

Daisy-chained BITS sources are not supported on the NCS.

Solution

Daisy-chained BITS sources cause additional wander buildup in the network and are therefore not

supported. Instead, use a timing signal generator to create multiple copies of the BITS clock and separately
link them to each NCS.

Blinking STAT LED after Installing a Card

Problem

After installing a card, the STAT LED blinks continuously for more than 60 seconds.

Possible Cause

The card cannot boot because it failed the Power On Shelf Test (POST) diagnostics.

The blinking STAT LED indicates that POST diagnostics are being performed. If the LED continues to blink
for more than 60 seconds, the card has failed the POST diagnostics test and has failed to boot. If the card has
truly failed, an

Alarm Troubleshooting, on page 99

is raised against the slot number with an Equipment

Failure description. Check the alarm tab for this alarm to appear for the slot where the card was installed. To
attempt recovery, remove and reinstall the card and observe the card boot process. If the card fails to boot,
replace the card. Complete the

Alarm Troubleshooting, on page 99

Solution

Solution

High-performance devices on this card can get hot during operation. To remove the card, hold

it by the faceplate and bottom edge. Allow the card to cool before touching any other part of it or before
placing it in an antistatic bag.

Statement 201

Warning

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

58

General Troubleshooting

Free-Running Synchronization Mode

«
...
102
103
104
105
106
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Express EtherNetwork DFE-670TXD

Бренд: D-Link Страницы: 4

Бренд: DAD Страницы: 36

Бренд: D-Link Страницы: 2

Бренд: National Instruments Страницы: 26

Бренд: National Instruments Страницы: 85

Module SCXI-1503

Бренд: National Instruments Страницы: 79

SCSI PC Card REX-9530V

Бренд: Ratoc Systems Страницы: 30

Armor 101 Series

Бренд: Lochinvar Страницы: 28

Armor 101 Series

Бренд: Lochinvar Страницы: 44

Бренд: Axis Страницы: 104

Бренд: Intel Страницы: 108

Бренд: IBASE Technology Страницы: 71

Бренд: Net to Net Technologies Страницы: 4

Бренд: Keithley Страницы: 98

Бренд: EVOC Страницы: 57

Бренд: IEI Technology Страницы: 3

Бренд: Eneo Страницы: 68

Бренд: JUMO Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды