Cisco NCS 2000 series Скачать руководство пользователя страница 203 | Manualshive

Страница: 203 / 602

background image

3.

Verify that the MA-Domain Mapping is correct. Click

Provisioning

>

CFM

>

Configuration

>

MA-Domain Mapping

DETAILED STEPS

Step 1

In card view, click the

Provisioning

>

CFM

>

Configuration

>

MEP

tabs.

Step 2

Do the following to ensure that the maintenance association and the domain names are the same.

a) In card view, click the

Provisioning

>

CFM

>

Configuration

>

MA Profiles

tabs.

b) Enter or note down the maintenance profile name.
c) In card view, click the

Provisioning

>

CFM

>

Configuration

>

Domain Profiles

tabs.

d) Enter or note down the domain profile name.
e) Repeat steps a to d on the other end of the maintenance end point.

The maintenance profile name and the domain profile name must be the same on both the maintenance end points.

Step 3

Verify that the MA-Domain Mapping is correct. Click

Provisioning

>

CFM

>

Configuration

>

MA-Domain Mapping

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

CHANLOSS

Default Severity: Not Alarmed (NA), Non-Service-Affecting (NSA)

Logical Object: OCN

The SONET Section Layer DCC Termination Failure condition occurs when the NCS receives unrecognized
data in the section layer DCC bytes.

Invisible laser radiation could be emitted from the end of the unterminated fiber cable or connector.
Do not stare into the beam directly with optical instruments. Viewing the laser output with certain
optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm
could pose an eye hazard.

Statement 1056

Warning

Use of controls, adjustments, or performing procedures other than those specified could result in
hazardous radiation exposure.

Statement 1057

Warning

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

157

Alarm Troubleshooting

CHANLOSS

«
...
201
202
203
204
205
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Express Ethernetwork DI-704P

Бренд: D-Link Страницы: 17

Бренд: ZALMAN Страницы: 20

Бренд: Aastra Страницы: 2

Бренд: NXP Semiconductors Страницы: 24

Бренд: WaiLan Страницы: 27

FieldPoint cFP-RTD-122

Бренд: National Instruments Страницы: 15

Бренд: Netis Страницы: 16

Бренд: Moxa Technologies Страницы: 2

Бренд: IBM Страницы: 34

TeleCLIENT TC7730 Series

Бренд: ETL Страницы: 83

Бренд: DigiTech Страницы: 6

Бренд: Solwise Страницы: 7

PCMCIA High Speed Serial Card CE 232HSPCC

Бренд: B&B Electronics Страницы: 14

CORE 2 DUO E4000 - 3-2008

Бренд: Intel Страницы: 122

JetStream T2600G-28TS

Бренд: TP-Link Страницы: 1136

Бренд: DPS Telecom Страницы: 80

ELITE LCD UPGRADE KIT

Бренд: Corsair Страницы: 11

Бренд: Garderos Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды