Cisco NCS 2000 series Скачать руководство пользователя страница 528 | Manualshive

Страница: 528 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

Refer to the warning message text.

You have selected Java version {0}. This version is
outside of the recommended range and may cause an
unpredictable behavior of the software. Do you wish
to continue?

WID-1042

Check for possible causes and try
again.

Error writing to file: {0}. This might be caused by a
directory permission, quota or disk volume full issue.

EID-1043

Refer to the warning message text.

Warning: there is a discrepancy in the build timestamp
between the NE cached jar file ({0}) and the NE ({1}).
Your CTC jar cache should be emptied.

WID-1044

The CTC software version must be
greater than or equal to the software
version on the node being managed.

Selected CTC version ({0}) must be greater than or
equal{to the login NE version ({1}).

EID-1046

Refer to the error message text.

No additional Pseudo IOS windows may be opened at
this time. The maximum number of Pseudo IOS
windows are open.

EID-1047

Refer to the error message text.

This Pseudo IOS connection has been terminated.
Terminations are caused when the session has timed
out, the node resets, or when the exit command has
been invoked.

This may also occur when the maximum number of
concurrent Pseudo IOS connections has been reached.

EID-1048

Refer to the error message text.

A Pseudo IOS connection cannot be opened right now
on this node. Please try again later.

EID-1049

Refer to the error message text.

Connection failed on node {0}

EID-1050

No rolls were selected for the bridge
and roll.

No rolls were selected. {0}

EID-2001

You cannot delete the roll unless it has
been completed or cancelled.

The roll must be completed or canceled before it can
be deleted.

EID-2002

There was an error when CTC tried to
delete the roll.

An error occurred while deleting the roll. {0}

EID-2003

You did not select a Cisco IOS slot.

No Cisco IOS slot was selected.

EID-2004

CTC cannot find the online help files
for the specified window. The files
might have been moved, deleted, or
not installed. To install online help,
run the setup program on the software
CD.

CTC cannot find the online help files for {0}. The files
might have been moved, deleted, or not installed. To
install online help, run the setup program on the
software CD.

EID-2005

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

482

Error Messages

Error Messages Reference

«
...
526
527
528
529
530
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: 3Com Страницы: 8

8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink

Бренд: Tyco Electronics Страницы: 18

Бренд: Garland Страницы: 4

Module NI PXI-8250

Бренд: National Instruments Страницы: 39

Бренд: Zenith Data Systems Страницы: 64

Бренд: RadiSys Страницы: 44

Бренд: Edge-Core Страницы: 7

RIPWAVE 40-00460-00R

Бренд: Navini Networks Страницы: 35

Бренд: Cypress Semiconductor Страницы: 10

Barricade SMC7901WBRA2

Бренд: SMC Networks Страницы: 2

Бренд: Paradyne Страницы: 23

Vigor 2760 Series

Бренд: Draytek Страницы: 54

Бренд: Juniper Страницы: 825

Бренд: OpenVox Страницы: 13

Active Module Carrier VX402C-64

Бренд: C&H Страницы: 32

Бренд: SafeHome Страницы: 24

Бренд: Hawking Страницы: 21

TGXPS-1080-M12-MV Series

Бренд: ORiNG Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды