Cisco NCS 2000 series Скачать руководство пользователя страница 483 | Manualshive

Страница: 483 / 602

background image

WTR is an informational condition and does not require troubleshooting.

Note

WTR (TRUNK)

Default Severity: Not Alarmed (NA), Non-Service-Affecting (NSA)

Logical Object: TRUNK

The Wait To Restore condition occurs when the

WKSWPR (TRUNK), on page 435

condition, is raised for

MXP or TXP splitter protection scheme ports. The condition occurs when the wait-to-restore time has not
expired, meaning that the active protect path cannot revert to the working path. The condition clears when
the timer expires and traffic switches back to the working path.

WTR is an informational condition and does not require troubleshooting.

Note

WVL-DRIFT-CHAN-OFF

Default Severity: Not Reported (NR), Service-Affecting (SA)

Logical Object: OCH

The Wavelength Channel OFF (WVL_CHAN_OFF) condition occurs in 40-SMR1-C, 40-SMR2-C, 80-WXC-C,
40-WXC-C, or 40-WSS-C cards. The condition detects slow variation in wavelength or optical power of a
TXP Trunk-TX port connected to an MSTP multiplexer.

WVL-DRIFT-CHAN-OFF alarm occurs in different ports depending on the type of card:

• In the 80-WXC-C or 40-WXC-C cards, COM-TX port for ADD/DROP and EXP/PT circuits.

• In the 40-SMR1-C or 40-SMR2-C cards, LINE-TX port for ADD/DROP and EXP/PT circuits.

• In the 40-WSS-C card, CHAN-RX port for ADD/DROP circuits and PT port for pass through circuits.

Clear the WVL-DRIFT-CHAN-OFF Condition

SUMMARY STEPS

1.

WVL-DRIFT-CHAN-OFF condition clears in the following scenarios:

DETAILED STEPS

WVL-DRIFT-CHAN-OFF condition clears in the following scenarios:

• OCH port is forced OOS.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

437

Alarm Troubleshooting

WTR (TRUNK)

«
...
481
482
483
484
485
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Univerge SV9300

Бренд: NEC Страницы: 26

Бренд: NEC Страницы: 20

DS2000 IntraMail

Бренд: NEC Страницы: 2

Бренд: Cambium Networks Страницы: 29

Бренд: Palo Alto Network Страницы: 56

Бренд: YASKAWA Страницы: 34

Бренд: Datasat Страницы: 170

Бренд: Zhone Страницы: 7

Бренд: Zhone Страницы: 1

Бренд: RAK Страницы: 30

Бренд: Kontron Страницы: 42

Бренд: Omron Страницы: 13

Бренд: Xantech Страницы: 4

E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV 27-9-2010

Бренд: Juniper Страницы: 122

Бренд: Lanner Страницы: 141

Бренд: Cypress Semiconductor Страницы: 38

Бренд: XtendLan Страницы: 17

Бренд: Infoblox Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды