manualshive.com logo in svg

Cisco NCS 2000 series, Руководство по устранению неисправностей

"Бесплатный Troubleshooting Manual для Cisco NCS 2000 series теперь доступен для скачивания с manualshive.com. Этот manual поможет вам настроить и обслуживать ваш продукт Cisco, обеспечивая стабильную работу сети. Загрузите его бесплатно прямо сейчас и узнайте все секреты работы с Cisco NCS 2000 series."

Поделиться
Скачать
background image

7.

If the signal is valid, ensure that the transmit and receive outputs from the patch panel to your equipment
are properly connected. For more information about fiber connections and terminations, refer to the
Turn Up a Node chapter in the Configuration guide.

8.

If a valid signal exists but the alarm does not clear, replace the cable connector on the NCS system.

9.

Repeat Steps

Step 2, on page 275

through

Step 6, on page 275

for any other port on the card that reports

the LOS (ESCON).

10.

If the alarm does not clear, the cabling could still be faulty despite correct attachments. Use the test set
to locate the bad cable and replace it using the procedures in the Configuration guide.

11.

If the alarm does not clear, look for any card-level alarm that could cause this port alarm.

12.

If the alarm does not clear, complete the

Physically Replace a Card, on page 453

procedure for the

reporting card.

DETAILED STEPS

Step 1

Check for any upstream equipment failures that could cause the ESCON LOS alarm in this node.

Step 2

If there is no cause upstream, verify cabling continuity from the transmitting port to the receiving port reporting this
LOS. To verify cable continuity, follow site practices.

Always use the supplied electrostatic discharge wristband when working with a powered NCS system. Plug
the wristband cable into the ESD jack located on the lower-right edge of the shelf assembly.

Caution

Step 3

If the continuity is good, clean the fiber according to site practice. If none exists, complete the fiber-cleaning procedure
in the Maintain the Node chapter in the Configuration guide.

Step 4

Ensure that the PPM (SFP) is correctly configured for this payload:

a) In node view (single-shelf mode) or shelf view (multishelf mode), double-click the card to open the card view.
b) Click the

Provisioning

>

Pluggable Port Modules

tabs.

c) Check the

Pluggable Port Modules

area for the PPM (SFP) associated with the port.

d) In the Pluggable Ports area, ensure that the rate for the errored PPM (SFP) is ESCON.

For information about provisioning PPMs (SFPs), refer to the Turn Up a Node chapter in the Configuration
guide. PPM (SFP) specifications are listed in the the

Installing the GBIC, SFP, SFP+, and XFP Optical

Modules in Cisco ONS PlatformsInstalling the GBIC, SFP, SFP+, QSFP, XFP, CXP, CFP and CPAK
Optical Modules in Cisco NCS Platforms

document.

Note

Step 5

If the physical cabling and PPM (SFP) are good but the alarm does not clear, verify that the correct port is actually in
service:

a) Confirm that the LED is correctly lit on the physical TXP card.

A green ACT/SBY LED indicates an active card. An amber ACT/SBY LED indicates a standby card.

b) To determine whether the port is in service, double-click the card in CTC to open the card view.
c) Click the

Provisioning

>

Line

tabs.

d) Verify that the Admin State column lists the port as IS, or (Unlocked).
e) If the Admin State column lists the port as OOS,MT (or Locked,maintenance) or OOS,DSBLD (or Locked,disabled),

click the column and choose

IS

or

Unlocked

. Click

Apply

.

Step 6

If the correct port is in service but the alarm has not cleared, use an optical test set to confirm that a valid signal exists
on the line. For specific procedures to use the test set equipment, consult the manufacturer. Test the line as close to the
receiving card as possible.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

275

Alarm Troubleshooting

Clear the LOS (ESCON) Alarm

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Aaeon UP Squared 6000 Edge Computing Kit User Manual preview
UP Squared 6000 Edge Computing Kit
Бренд: Aaeon Страницы: 59
National Instruments NI 5922 Calibration Procedure preview
NI 5922
Бренд: National Instruments Страницы: 28
National Instruments NI 9219 Getting Started preview
NI 9219
Бренд: National Instruments Страницы: 19
National Instruments NI 9219 Operating Instructions Manual preview
NI 9219
Бренд: National Instruments Страницы: 36
National Instruments NI 6711 User Manual preview
NI 6711
Бренд: National Instruments Страницы: 103
National Instruments NI PXI-1042 Series Installation Manual preview
NI PXI-1042 Series
Бренд: National Instruments Страницы: 12
National Instruments PCI-1407 Setup And Operation preview
PCI-1407
Бренд: National Instruments Страницы: 4
Belkin F5D9001 Series Manual preview
F5D9001 Series
Бренд: Belkin Страницы: 72
Helmholz REX 200 Quick Start Manual preview
REX 200
Бренд: Helmholz Страницы: 28
ADC HiGain HLU-231 List 8F Quick Installation preview
HiGain HLU-231 List 8F
Бренд: ADC Страницы: 7
Lancom 1821n Wireless Manual preview
1821n Wireless
Бренд: Lancom Страницы: 102
vPipes Uilleann Quick Start Manual preview
Uilleann
Бренд: vPipes Страницы: 3
Baldor Modbus Plus Installation And Operating Manual preview
Modbus Plus
Бренд: Baldor Страницы: 34
IntesisBox IBOX-BAC Series Installation Sheet preview
IBOX-BAC Series
Бренд: IntesisBox Страницы: 2
Linksys WRT54GR - Wireless-G Broadband Router Quick Installation Manual preview
WRT54GR - Wireless-G Broadband Router
Бренд: Linksys Страницы: 81
Kanguru Data Bank User Manual preview
Data Bank
Бренд: Kanguru Страницы: 13
Magma ExpressBox2 EB2 User Manual preview
ExpressBox2 EB2
Бренд: Magma Страницы: 74
Z-Com ZCN-1523H-5-16 Quick Installation Manual preview
ZCN-1523H-5-16
Бренд: Z-Com Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды