Cisco NCS 2000 series Скачать руководство пользователя страница 268 | Manualshive

Страница: 268 / 602

background image

5.

If the alarm does not clear, complete the

Physically Replace a Card, on page 453

procedure for the reporting

MXP or TXP card.

DETAILED STEPS

Step 1

In node view (single-shelf mode) or shelf view (multishelf mode), double-click the TXP or MXP card to open the card
view.

Step 2

Click the

Performance

>

Optics PM

>

Current Values

tabs.

Step 3

Verify the card laser temperature levels. Maximum, minimum, and average laser temperatures are shown in the Current
column entries in the Laser Temp rows.

Step 4

Complete the

Reset a Card in CTC, on page 449

procedure for the MXP or TXP card.

Step 5

If the alarm does not clear, complete the

Physically Replace a Card, on page 453

procedure for the reporting MXP or TXP

card.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

HI-RXPOWER

Default Severity: Minor (MN), Non-Service-Affecting (NSA)

Logical Objects: 2R, ESCON, FC, GE, ISC, OCN/STMN, TRUNK, EQPT

The Equipment High Receive Power alarm is an indicator of the optical signal power that is transmitted to
the TXP_MR_10G, TXP_MR_2.5G, TXPP_MR_2.5G, TXP_MR_10E, TXP_MR_10E_C, TXP_MR_10E_L,
MXP_2.5G_10G, OC192-XFP, GE-XP, 10GE-XP, ADM-10G, or OTU2_XP card. HI-RXPOWER occurs
when the measured optical power of the received signal exceeds the threshold. The threshold value is
user-provisionable.

Clear the HI-RXPOWER Alarm

SUMMARY STEPS

1.

Check the PM of the TRUNK-RX port. Verify that received power is above the optics threshold:

2.

Verify that the Trunk-Rx port is cabled correctly, and clean the fiber connecting the faulty TXP/MXP to
the Drop port of the DWDM card (32DMX, or 40DMX). If no site cleaning practices are available, refer
to the fiber cleaning procedure in the Maintain the Node chapter of the Configuration Guide.

3.

Determine whether a bulk attenuator is specified by the Cisco Transport Planner design. If so, verify that
the proper fixed attenuation value has been used.

4.

Using a test set, check the optical power value of the Drop port of the DWDM card (32DMX, or 40DMX)
connected to the faulty TXP/MXP. If the read value is different (+1 dBm or 1 dBm) from the ANS setpoint
for Padd&drop-Drop power, move to next step.

5.

Look for and troubleshoot any alarm reported by the cards belonging to the OCHNC circuit destinating
at the faulty TXP/MXP. Possible alarms include amplifier Gain alarms (the

GAIN-HDEG , on page 208

alarm, the

GAIN-HFAIL , on page 210

alarm, the

GAIN-LDEG , on page 211

alarm, or

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

222

Alarm Troubleshooting

HI-RXPOWER

«
...
266
267
268
269
270
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: IBM Страницы: 86

Бренд: H3C Страницы: 34

Бренд: LAWO Страницы: 154

Бренд: N-Tron Страницы: 62

Бренд: Zonet Страницы: 10

Бренд: Samsung Страницы: 65

Бренд: RadiSys Страницы: 44

INTERNET PRIVACY PROTECTION

Бренд: AlphaShield Страницы: 49

Бренд: Compaq Страницы: 112

RouterBOARD SXT 5HnD

Бренд: MikroTik Страницы: 2

HiGain HLU-231 List 8F

Бренд: ADC Страницы: 7

Magic WiFi mini Ek

Бренд: Devolo Страницы: 22

Бренд: U.S. Products Страницы: 80

Бренд: Wintech Страницы: 21

Бренд: Idis Страницы: 85

Бренд: ProCurve Страницы: 2

Бренд: Sangoma Страницы: 6

Бренд: PMD Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды