Cisco NCS 2000 series Скачать руководство пользователя страница 541

Страница: 541 / 602

Description

Error/Warning Message

Error/Warning
ID

You must select a node for the
upgrade.

No node was selected for upgrade.

EID-2211

The protected line cannot be
provisioned. Choose another line.

A protected line is not provisionable.

EID-2212

The circuit state, specified by {0}
cannot be applied to the selected
drops.

The current type or state of some drops does not allow
the new circuit state of {0} to be applied to them
indirectly.

WID-2213

Refer to the error message text.

The node is disconnected. Please wait until the node
reconnects.

EID-2214

There was an error while leaving the
specified page.

An error occurred while leaving the {0} page.

EID-2215

There was an error while entering the
specified page.

An error occurred while entering the {0} page.

EID-2216

Refer to the error message text.

Some conditions could not be retrieved from the
network view

EID-2217

The bandwidth must be within the
specified parameters.

The bandwidth must be between {0} and {1} percent.

EID-2218

As the protection operation failed, a
cross-connect (XC) loopback will be
applied on cross-connection.

The protection operation failed. An XC loopback was
applied on the cross-connection.

EID-2219

Refer to the error message text.

The tunnel status is PARTIAL. CTC is not able to
change it. Please try again later.

EID-2220

Refer to the error message text.

A valid route cannot be found for the unprotected to
{0} upgrade request.

EID-2221

The nodes, specified by {1}, are
already part of a 4-fiber
BLSR/MS-SPRing type (specified by
{0}).

One or more of the following nodes are currently part
of a four-fiber {0}. Only a single four-fiber {0} is
supported per node. {1}

EID-2222

Refer to the error message text.

Only one circuit can be upgraded at a time.

EID-2223

Refer to the error message text.

This link may not be included because it terminates on
the source.

EID-2224

Roll can be completed only when a
valid signal is detected. If not, the roll
completion may result in an error.

A valid signal could not be detected while trying to
complete the roll. {0}

EID-2225

Refer to the error message text.

The circuit roll failed. {0}

EID-2226

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

495

Error Messages

Error Messages Reference

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание NCS 2000 series

Отзывы:

Похожие инструкции для NCS 2000 series

Бренды по названию

Популярные бренды

Cisco NCS 2000 series, Руководство по устранению неисправностей

Результаты поиска

Содержание NCS 2000 series

Отзывы:

Похожие инструкции для NCS 2000 series

Бренды по названию

Популярные бренды