Cisco NCS 2000 series Скачать руководство пользователя страница 595 | Manualshive

Страница: 595 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

Refer to the error message text.

The CRS node {0} version[{1}] is greater than the
supported version[{2}]. The creation of ochtrail circuits
between CRS nodes will not be disabled, but there could
be unexpected behaviors.

EID-6326

Refer to the error message text.

The end point of patchcord have an incompatible
wavelength.

EID-6327

Refer to the error message text.

Protection/AIS action cannot be both set to squelch.

EID-6329

Refer to the error message text.

The node failed to restart the Pseudo IOS CLI service
on the selected port. Try using another unreserved port
that is not being used within the 1024 - 65535 range.

EID-6330

Refer to the error message text.

That port is already in use. Also note that the Pseudo
IOS port may not be changed if any Pseudo IOS
connections are currently open.

EID-6331

Refer to the warning message text.

All previously configured IPv6 destinations will become
unreachable if IPv6 mode is disabled. It is
recommended that you remove all IPv6 related
provisioning before disabling IPv6 mode. Do you want
to continue?

WID-6332

Refer to the warning message text.

The NE default {0} not available in the selected NE
Defaults Tree.

WID-6333

Refer to the warning message text.

Could not find the NE default {0}.

WID-6334

Refer to the warning message text.

CTC was unable to create a new Target account.

WID-6335

Refer to the warning message text.

Changing the card to EFEC mode will cause the ports
1 and 2 to be disabled. Do you want to continue?

WID-6336

Refer to the warning message text.

CE-MR-10/CE-MR-6 card does not validate the
Ethernet FCS when traffic is received from optical side.
This can result in errored frames from optical side being
forwarded to the peer device via front ports. It would
be left to the peer device to detect the errors and discard
the frames. It is suggested to enable the FCS option on
both ends of the circuit. The GFP FCS will be used to
discard errored frames. The discarded frames will be
accounted under the performance pane for the POS
port.

WID-6337

Refer to the warning message text.

Ingress COS setting is not compatible with QinQ mode.

WID-6338

Refer to the warning message text.

Some circuits may become partial as part of this
upgrade and would need to be reconfigured.

WID-6339

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

549

Error Messages

Error Messages Reference

«
...
593
594
595
596
597
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Univerge SV9300

Бренд: NEC Страницы: 26

Бренд: NEC Страницы: 20

DS2000 IntraMail

Бренд: NEC Страницы: 2

Бренд: Octavo Страницы: 28

Бренд: Obihai Страницы: 2

X-Pedition 2000

Бренд: Enterasys Страницы: 86

Fast SwitchHub-8mi SNMP

Бренд: Accton Technology Страницы: 13

Compact Emulator M30620T-CPE

Бренд: Renesas Страницы: 52

Бренд: Teac Страницы: 20

cMT-FHDX Series

Бренд: Maple Systems Страницы: 2

Бренд: NETGEAR Страницы: 2

Бренд: Allied Telesis Страницы: 1

Бренд: HARTING Страницы: 13

Бренд: TP-Link Страницы: 131

Бренд: Omron Страницы: 6

Бренд: TP-Link Страницы: 2

Бренд: ICOP Technology Страницы: 34

POD-51EH-C541U-12

Бренд: IceTech Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды