manualshive.com logo in svg

Cisco NCS 2000 series, Руководство по устранению неисправностей

"Бесплатный Troubleshooting Manual для Cisco NCS 2000 series теперь доступен для скачивания с manualshive.com. Этот manual поможет вам настроить и обслуживать ваш продукт Cisco, обеспечивая стабильную работу сети. Загрузите его бесплатно прямо сейчас и узнайте все секреты работы с Cisco NCS 2000 series."

Поделиться
Скачать
background image

13.

If no other alarms exist that could be the source of the OPWR-HDEG, or if clearing an alarm did not
clear the alarm, place all of the card ports in

OOS,DSBLD

(or

Locked,disabled

) administrative state.

14.

Complete the

Physically Replace a Card, on page 453

procedure for the reporting card.

DETAILED STEPS

Step 1

Verify fiber continuity to the port by following site practices. Refer to the Network Reference chapter of the Configuration
guide for a procedure to detect a fiber cut.

Step 2

If the cabling is good, confirm that the LED is correctly illuminated on the physical card. A green ACT/SBY LED
indicates an active card. A red ACT/SBY LED indicates a failed card.

Step 3

Verify that the power read by photodiode on the port is within the expected range as projected by Cisco TransportPlanner.
The application generates a spreadsheet of values containing this information.

Step 4

If the optical power level is within specifications, check the opwrMin threshold. (These are listed in the Configuration
guide.) Refer to the

Cisco Transport Planner DWDM Operations Guide

and decide what value to use for modifying

the power level:

a) In node view (single-shelf mode) or shelf view (multishelf mode), double-click the card to open the card view.
b) Display the optical thresholds by clicking the following tabs:

• For the OPT-BST, OPT-AMP-C, or OPT-AMP-17-C cards, click the

Provisioning

>

Opt. Ampli. Line

>

Optics Thresholds

tabs.

• For the OPT-PRE, OPT-AMP-C, or OPT-AMP-17-C cards, click the

Provisioning

>

Opt. Ampli. Line

>

Optics Thresholds

tabs.

• For the WXC card, click the

Provisioning

>

Optical Chn

>

Optics Thresholds

tabs.

• For the AD-xC-xx.x card, click the

Provisioning

>

Optical Chn

>

Optics Thresholds

tabs.

• For the AD-xB-xx.x card, click the

Provisioning

>

Optical Band

>

Optics Thresholds

tabs.

•
•
• For the 32WSS card, click the

Provisioning

>

Optical Chn: Optical Connector x

>

Optics Thresholds

tabs.

• For the OSCM or OSC-CSM cards, click the

Provisioning

>

Optical Line

>

Optics Thresholds

tabs.

• For the 40-SMR1-C and 40-SMR2-C cards, click the

Provisioning

>

Optical Line

>

Optics Thresholds

tabs.

Step 5

If the received optical power level is within specifications, refer to the

Cisco Transport Planner DWDM Operations

Guide

to determine the correct levels and check the opwrMin threshold. (These are listed in the Configuration guide.)

If necessary, modify the value as required.

Step 6

If the optical power is outside of the expected range, verify that all involved optical signal sources, namely the TXP or
MXP trunk port or an ITU-T line card, are in IS administrative state by clicking the correct tab:

• For the MXPP_MR_2.5G card, click the

Provisioning

>

Line

>

SONET

(or

Provisioning

>

Line

>

SDH

) tabs.

• For the MXP_2.5G_10E card, click the

Provisioning

>

Line

> Trunk tabs.

• For the MXP_2.5G_10G card, click the

Provisioning

>

Line

>

SONET

(or

Provisioning

>

Line

>

SDH

) tabs.

• For the MXP_MR_2.5G card, click the

Provisioning

>

Line

>

SONET

(or

Provisioning

>

Line

>

SDH

) tabs.

• For the TXPP_MR_2.5G card, click the

Provisioning

>

Line

>

SONET

(or

Provisioning

>

Line

>

SDH

) tabs.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

324

Alarm Troubleshooting

Clear the OPWR-HDEG Alarm

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Abocom FW200 Specifications preview
FW200
Бренд: Abocom Страницы: 1
Harmonic XOS User Manual preview
XOS
Бренд: Harmonic Страницы: 56
Ebyte E103-W13 User Manual preview
E103-W13
Бренд: Ebyte Страницы: 14
IDT USB-BRIDGEV2-EVAL Evaluation Board Manual preview
USB-BRIDGEV2-EVAL
Бренд: IDT Страницы: 11
ebm-papst R3G175-AF01-02 Operating Instructions Manual preview
R3G175-AF01-02
Бренд: ebm-papst Страницы: 11
C-Com IPAM-1600s Series User Manual preview
IPAM-1600s Series
Бренд: C-Com Страницы: 148
TP-Link TL-MR3220 Quick Installation Manual preview
TL-MR3220
Бренд: TP-Link Страницы: 87
HighPoint RocketCache 3240X8 User Manual preview
RocketCache 3240X8
Бренд: HighPoint Страницы: 17
Patton DiamondLink 3201 Quick Start Manual preview
DiamondLink 3201
Бренд: Patton Страницы: 12
Fastech Ezi-SERVOII EtherCAT TO User Manual preview
Ezi-SERVOII EtherCAT TO
Бренд: Fastech Страницы: 108
Global411 MS41p1 Quick Installation Manual preview
MS41p1
Бренд: Global411 Страницы: 15
ZyXEL Communications G-170S User Manual preview
G-170S
Бренд: ZyXEL Communications Страницы: 79
ICOP Technology Vortex86SX VSX-6100 User Manual preview
Vortex86SX VSX-6100
Бренд: ICOP Technology Страницы: 50
Hunter Pro-C Series Programming Instructions preview
Pro-C Series
Бренд: Hunter Страницы: 2
QTech QSW-2900 User Manual preview
QSW-2900
Бренд: QTech Страницы: 406
Navitar 1-62643 Dimensional Drawing preview
1-62643
Бренд: Navitar Страницы: 1
ENERMAX ELC-LMT120-RGB User Manual preview
ELC-LMT120-RGB
Бренд: ENERMAX Страницы: 33
Xinje VH5 Series User Manual preview
VH5 Series
Бренд: Xinje Страницы: 76

Бренды по названию

Популярные бренды

Загрузить еще бренды