Cisco NCS 2000 series Скачать руководство пользователя страница 201 | Manualshive

Страница: 201 / 602

background image

b) Select or note down the CC Timer value.
c) Repeat step a and b on the other end of the maintenance end point.
d) Set the CC Timer value that is same as the value set at the other maintenance end point.

Step 3

Verify the maintenance association and the domain name are the same. Do the following:

a) In card view, click the

Provisioning

>

CFM

>

Configuration

>

MA Profiles

tabs.

b) Enter or note down the maintenance profile name.
c) In card view, click the

Provisioning

>

CFM

>

Configuration

>

Domain Profiles

tabs.

d) Enter or note down the domain profile name.
e) Repeat step a and d on the other end of the maintenance end point.
f)

The maintenance profile name and the domain profile name should be the same on both the maintenance end points.

Step 4

Verify the maintenance point (MP) ID on both the sides are the same. Do the following:

a) In card view, click the

Provisioning

>

CFM

>

Configuration

>

MEP

tabs.

b) Note down the MPID value.
c) MPID should not be the same.
d) Repeat step a and d on the other end of the maintenance end point.
e) The MPID values must not be the same on both the maintenance end points.

CFM-LOOP

Default Severity: Minor (MN), Non-Service-Affecting (NSA)

Logical Objects: ETH

The Connectivity Fault Management Loop (CFM-LOOP) alarm occurs on GE_XP or 10GE_XP cards when
a continuity check (CC) packet is reused in a loop and consequently the same packet is returned to the source.

Clear the CFM-LOOP Condition

SUMMARY STEPS

1.

Ensure that there are no loops in the L2-over-DWDM mode for VLANs in the network.

DETAILED STEPS

Ensure that there are no loops in the L2-over-DWDM mode for VLANs in the network.

If the alarm does not get cleared, you need to report a Service-Affecting (SA) problem. Log into the Technical Support
Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or log into

http://www.cisco.com/c/

en/us/support/web/tsd-cisco-worldwide-contacts.html

to obtain a directory of toll-free Technical Support numbers for

your country.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

155

Alarm Troubleshooting

CFM-LOOP

«
...
199
200
201
202
203
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 9

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 28

Бренд: D-Link Страницы: 2

DSL-2540B - ADSL2/2+ Modem With EN Router

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 62

Бренд: EAW Страницы: 2

Бренд: ICP DAS USA Страницы: 14

Бренд: ICP DAS USA Страницы: 25

Бренд: ICP DAS USA Страницы: 15

Бренд: ICP DAS USA Страницы: 8

Бренд: ICP Страницы: 14

Бренд: PaloAlto Networks Страницы: 3

EK-FC780 GTX Jetstream

Бренд: ekwb Страницы: 2

iW-RainboW-G30D

Бренд: iWave Страницы: 89

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды