manualshive.com logo in svg

Cisco NCS 2000 series, Руководство по устранению неисправностей

"Бесплатный Troubleshooting Manual для Cisco NCS 2000 series теперь доступен для скачивания с manualshive.com. Этот manual поможет вам настроить и обслуживать ваш продукт Cisco, обеспечивая стабильную работу сети. Загрузите его бесплатно прямо сейчас и узнайте все секреты работы с Cisco NCS 2000 series."

Поделиться
Скачать
background image

2.

If both nodes do not use the same Layer 2 settings, you will have to delete the incorrect termination and
recreate it. To delete it, click the termination and click

Delete

. To recreate it, refer to the Turn Up Node

chapter in the Configuration guide for the procedure.

3.

If the nodes use PPP Layer 2, complete the

Clear the RS-EOC Alarm, on page 381

procedure. If the alarm

does not clear, go to

Step 7, on page 245

.

4.

If both nodes use the LAPD Layer 2 protocol but have different Mode settings, change the incorrect node
entry by clicking the correct setting radio button in the Edit MSDCC termination dialog box and clicking

OK

.

5.

If the Layer 2 protocol and Mode settings are correct, ensure that one node is using the Network role and
the other has the User role. If not (that is, if both have the same mode settings), correct the incorrect one
by clicking the correct radio button in the Edit MSDCC termination dialog box and clicking

OK

.

6.

If the Layer 2, Mode, and Role settings are correct, compare the MTU settings for each node. If one is
incorrect, choose the correct value in the Edit MSDCC dialog box and click

OK

.

7.

If all of the preceding settings are correct, ensure that OSI routers are enabled for the communications
channels at both ends by completing the following steps:

8.

If the routers on both ends are enabled and the alarm still has not cleared, ensure that both ends of the
communications channel have a common MAA by completing the following steps:

DETAILED STEPS

Step 1

Ensure that both ends of the communication channel are using the correct Layer 2 protocol and settings (LAPD or PPP).
To do this, complete the following steps:

a) At the local node, in node view, click the

Provisioning

>

Comm Channels

>

MSDCC

tabs.

b) Click the row of the circuit. Click

Edit

.

c) In the Edit MSDCC termination dialog box, view and record the following selections: Layer 2 protocol (LAPD or

PPP); Mode radio button selection (AITS or UITS); Role radio button selection (Network or User); MTU value; T200
value, and T203 selections.

d) Click

Cancel

.

e) Log in to the remote node and follow the same steps, also recording the same information for this node.

Step 2

If both nodes do not use the same Layer 2 settings, you will have to delete the incorrect termination and recreate it. To
delete it, click the termination and click

Delete

. To recreate it, refer to the Turn Up Node chapter in the Configuration

guide for the procedure.

Step 3

If the nodes use PPP Layer 2, complete the

Clear the RS-EOC Alarm, on page 381

procedure. If the alarm does not clear,

go to

Step 7, on page 245

.

Step 4

If both nodes use the LAPD Layer 2 protocol but have different Mode settings, change the incorrect node entry by clicking
the correct setting radio button in the Edit MSDCC termination dialog box and clicking

OK

.

Step 5

If the Layer 2 protocol and Mode settings are correct, ensure that one node is using the Network role and the other has
the User role. If not (that is, if both have the same mode settings), correct the incorrect one by clicking the correct radio
button in the Edit MSDCC termination dialog box and clicking

OK

.

Step 6

If the Layer 2, Mode, and Role settings are correct, compare the MTU settings for each node. If one is incorrect, choose
the correct value in the Edit MSDCC dialog box and click

OK

.

Step 7

If all of the preceding settings are correct, ensure that OSI routers are enabled for the communications channels at both
ends by completing the following steps:

a) Click

Provisioning

>

OSI

>

Routers

>

Setup

.

b) View the router entry under the

Status

column. If the status is Enabled, check the other end.

c) If the Status is Disabled, click the router entry and click

Edit

.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

245

Alarm Troubleshooting

Clear the ISIS-ADJ-FAIL Alarm

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Dahua Smart 1U Quick Start Manual preview
Smart 1U
Бренд: Dahua Страницы: 24
Barco ImagePRO-HD Installation Manual preview
ImagePRO-HD
Бренд: Barco Страницы: 121
IEI Technology PUZZLE-IN003B User Manual preview
PUZZLE-IN003B
Бренд: IEI Technology Страницы: 86
Dahua Technology Lite N42B1P Series Quick Start Manual preview
Lite N42B1P Series
Бренд: Dahua Technology Страницы: 14
JUMO iTRON B 70.2040 Operating Instructions Manual preview
iTRON B 70.2040
Бренд: JUMO Страницы: 41
Techroutes TSR 2800-30 Hardware Installation Manual preview
TSR 2800-30
Бренд: Techroutes Страницы: 20
Airlinkplus ASW224 User Manual preview
ASW224
Бренд: Airlinkplus Страницы: 20
Handicare DX REM 420 User Manual preview
DX REM 420
Бренд: Handicare Страницы: 60
Zalip CDE570AM-U User Manual preview
CDE570AM-U
Бренд: Zalip Страницы: 76
TP-Link Archer MR600 User Manual preview
Archer MR600
Бренд: TP-Link Страницы: 113
VIA Technologies Mobile360 M810 Quick Start Manual preview
Mobile360 M810
Бренд: VIA Technologies Страницы: 25
Cypress Semiconductor CY8C24223A Specification Sheet preview
CY8C24223A
Бренд: Cypress Semiconductor Страницы: 31
Renesas R0E0144TNPFK00 User Manual preview
R0E0144TNPFK00
Бренд: Renesas Страницы: 4
Watchguard Firebox T20 Hardware Manual preview
Firebox T20
Бренд: Watchguard Страницы: 21
Inspired Energy ATA004N Operating Instructions preview
ATA004N
Бренд: Inspired Energy Страницы: 5
S&P Turbo-3000 Operating Instructions preview
Turbo-3000
Бренд: S&P Страницы: 3
ProSoft MVI46-PDPS User Manual preview
MVI46-PDPS
Бренд: ProSoft Страницы: 53
Renesas Emulation Memory Board R0E330850MSRC0 User Manual preview
Emulation Memory Board R0E330850MSRC0
Бренд: Renesas Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды