manualshive.com logo in svg

Cisco NCS 2000 series, Руководство по устранению неисправностей

"Бесплатный Troubleshooting Manual для Cisco NCS 2000 series теперь доступен для скачивания с manualshive.com. Этот manual поможет вам настроить и обслуживать ваш продукт Cisco, обеспечивая стабильную работу сети. Загрузите его бесплатно прямо сейчас и узнайте все секреты работы с Cisco NCS 2000 series."

Поделиться
Скачать
background image

Description

Error/Warning Message

Error/Warning
ID

Refer to the error message text.

You cannot delete this card: {0}.

EID-3170

CTC encountered an error creating the
trap destination.

An error occurred while creating the trap destination.

EID-3171

Select an RMON threshold.

No RMON thresholds were selected.

EID-3172

The specified contact exceeds the
specified character limit.

The contact ''{0}'' cannot exceed {1} characters.

EID-3173

The specified location exceeds the
specified character limit.

The description ''{0}'' cannot exceed {1} characters.

EID-3174

The specified operator identifier
exceeds the specified character limit.

The operator identifier ''{0}'' cannot exceed {1}
characters.

EID-3175

The specified operator specific
information exceeds the specified
character limit.

The operator specific information ''{0}'' cannot exceed
{1} characters.

EID-3176

The specified name is empty.

The node name cannot be empty.

EID-3177

The specified name exceeds the
specified character limit.

The node name ''{0}'' cannot exceed {1} characters.

EID-3178

Refer to the error message text.

The protect card is in use.

EID-3179

Create a 1+1 protection group.

The 1+1 protection group does not exist.

EID-3180

Refer to the error message text.

The Y-cable protection group does not exist.

EID-3181

You cannot delete the topology
element which is in use.

The topology element is in use and cannot be deleted
as requested.

EID-3182

CTC encountered an error while
deleting the protection group.

An error occurred while deleting the protection group.

EID-3183

You must select an item before
completing this task.

No {0} was selected.

EID-3184

Refer to the error message text.

This ring has an active protection switch operation and
cannot be deleted at this time.

EID-3185

The request cannot be completed.

The node is busy: {0} is {1} and cannot be deleted as
requested.

EID-3186

CTC encountered an error deleting the
trap destination.

An error occurred while deleting the trap destination.

EID-3187

The password you entered is invalid.
Enter the password again.

An error occurred during authentication. The password
entered is invalid.

EID-3188

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

506

Error Messages

Error Messages Reference

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

XMOS xCORE-200 Multi-channel Audio board Design Manual preview
xCORE-200 Multi-channel Audio board
Бренд: XMOS Страницы: 112
IBM 8677 - BladeCenter Rack-mountable - Power... Planning And Installation Manual preview
8677 - BladeCenter Rack-mountable - Power...
Бренд: IBM Страницы: 126
Maxim DS5001FP Specification Sheet preview
DS5001FP
Бренд: Maxim Страницы: 26
NetComm 3GM1WN Quick Start Manual preview
3GM1WN
Бренд: NetComm Страницы: 3
Supero AOC-SIMLC User Manual preview
AOC-SIMLC
Бренд: Supero Страницы: 68
e-con Systems ACC-CX3RDK-CU5640 Getting Started Manual preview
ACC-CX3RDK-CU5640
Бренд: e-con Systems Страницы: 9
Western Digital Scorpio WD2500BPVT Product Specifications preview
Scorpio WD2500BPVT
Бренд: Western Digital Страницы: 3
Western Digital Scorpio WD2500BPVT Product Features preview
Scorpio WD2500BPVT
Бренд: Western Digital Страницы: 4
Wintech TDS510USB Plus Installation Manual preview
TDS510USB Plus
Бренд: Wintech Страницы: 21
Maipu MP2900-04-AC Installation Manual preview
MP2900-04-AC
Бренд: Maipu Страницы: 80
Renesas R0E530650CFJ30 User Manual preview
R0E530650CFJ30
Бренд: Renesas Страницы: 4
ebm-papst W3G710-NK67-01 Operating Instructions Manual preview
W3G710-NK67-01
Бренд: ebm-papst Страницы: 13
ZALMAN RESERATOR1 V2 Installation And Operational Manual preview
RESERATOR1 V2
Бренд: ZALMAN Страницы: 18
Accton Technology MR3202A User Manual preview
MR3202A
Бренд: Accton Technology Страницы: 78
Razer RZ37-0251 Manual preview
RZ37-0251
Бренд: Razer Страницы: 17
Topcom Xplorer 871B (Norwegian) Hurtig Installasjonsveiledning preview
Xplorer 871B
Бренд: Topcom Страницы: 16
Xantech IR-X10 Installation Instructions Manual preview
IR-X10
Бренд: Xantech Страницы: 16
Hama 49062 Instruction Manual preview
49062
Бренд: Hama Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды