Cisco NCS 2000 series Скачать руководство пользователя страница 554 | Manualshive

Страница: 554 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

Refer to the error message text.

The current loopback provisioning does not allow this
state transition.

EID-3233

You cannot transition the port state to
the target date while in the current
synchronization state.

The current synchronization provisioning does not allow
this state transition.

EID-3234

Refer to the error message text.

The requested state transition cannot be performed on
this software version.

EID-3235

CTC failed to restore the specified
database.

The database restore failed. {0}

EID-3236

CTC failed to backup the specified
database.

The database backup failed. {0}

EID-3237

The send payload defect indicator path
(PDI-P) setting on the specified item
should be consistent with that of the
specified control node.

The send PDIP setting on {0} is inconsistent with the
setting on the control node {1}.

EID-3238

Refer to the error message text.

The overhead termination is invalid

EID-3239

Overhead terminations have exceeded
the limit.

The maximum number of overhead terminations has
been exceeded.

EID-3240

The specified termination port is in
use. Select another port.

The {0} termination port is in use.

EID-3241

The specified DCC already exists on
the selected port. You can create a
DCC of another type.

An {1} exists on the selected ports. Therefore, you must
create the {0}s one by one.

EID-3242

The same port can not be used by
multiple DCCs.

The port you have chosen as an {0} endpoint already
supports an {1}. The port cannot support both DCCs.
After the {0} is created, verify that no EOC alarms are
present and then delete the {1} to complete the
downgrade.

WID-3243

The specified DCC already exists on
the selected port. You can create a
DCC of another type.

An {0} exists on the selected ports. Therefore, you must
create the {1}s one by one.

EID-3244

The port selected as a DCC endpoint
already supports another DCC. Refer
to the warning message text.

The port you have chosen as an {1} endpoint already
supports an {0}. The port cannot support both DCCs.
After the {1} is created, verify that no EOC alarms are
present and then delete the {0} to complete the upgrade.

WID-3245

CTC encountered an error.

The wizard was not able to validate the data. {0}

EID-3246

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

508

Error Messages

Error Messages Reference

«
...
552
553
554
555
556
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: PaloAlto Networks Страницы: 3

Бренд: Paradyne Страницы: 20

Compshere 3000 Series

Бренд: Paradyne Страницы: 2

Бренд: Pantech Страницы: 17

Бренд: Vivotek Страницы: 136

Бренд: Alcad Страницы: 6

Бренд: Garderos Страницы: 23

Бренд: EnGenius Страницы: 3

Бренд: Patton electronics Страницы: 12

Бренд: ZyXEL Communications Страницы: 422

NetIron MLXe Series

Бренд: Brocade Communications Systems Страницы: 305

Бренд: TP-Link Страницы: 176

HIRESCHMANN IT MAMMUTHUS MTM8003-FAN

Бренд: Belden Страницы: 84

Mercury FireWire 400

Бренд: OWC Страницы: 2

Tamar FCSAS102800

Бренд: Bridgeworks Страницы: 56

High-Precision AD/DA Board

Бренд: Waveshare Страницы: 8

Бренд: Airlink101 Страницы: 64

Бренд: ETAS Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды