Cisco NCS 2000 series Скачать руководство пользователя страница 178

Страница: 178 / 602

AUTO-SENSE-DSBLD

Default Severity: Not Alarmed (NA), Non-Service-Affecting (NSA)

Logical Object: PPM

The AUTO-SENSE-DSBLD alarm is raised when the port is configured as an AUTO port, but auto-sensing
is disabled.

Clear the AUTO-SENSE-DSBLD Alarm

SUMMARY STEPS

Clear the AUTO-SENSE-DSBLD alarm with either of these procedures:

DETAILED STEPS

Clear the AUTO-SENSE-DSBLD alarm with either of these procedures:

a) Enable auto-sensing.

In node view (single-shelf mode) or shelf view (multishelf view), double-click the AR_MXP or AR_XP card
where you want to enable auto-sensing.

Click the

Provisioning

Line

Auto Ports

tabs.

Check the

Auto Sensing

check box.

b) Delete the auto port.

In node view (single-shelf mode) or shelf view (multishelf view), double-click the AR_MXP or AR_XP card
where you want to delete the auto port.

Click the

Provisioning

Pluggable Port Modules

tabs.

In the Pluggable Port Modules area, select the auto PPM that you want to delete and click

Delete

Click

Yes

. The auto port is deleted.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

AUTORESET

Default Severity: Minor (MN), Non-Service-Affecting (NSA)

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

132

Alarm Troubleshooting

AUTO-SENSE-DSBLD

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание NCS 2000 series

Отзывы:

Похожие инструкции для NCS 2000 series

Бренды по названию

Популярные бренды

Cisco NCS 2000 series, Руководство по устранению неисправностей

Результаты поиска

Содержание NCS 2000 series

Отзывы:

Похожие инструкции для NCS 2000 series

Бренды по названию

Популярные бренды