Cisco NCS 2000 series Скачать руководство пользователя страница 251 | Manualshive

Страница: 251 / 602

background image

Logical Object: TRUNK

The Force Switch Request Span condition applies to MXP and TXP trunk ports in splitter protection groups.
If traffic is present on a working port and you use the FORCE command to prevent it from switching to the
protect port (indicated by FORCED TO WORKING), FORCED-REQ-SPAN indicates this force switch. In
this case, the force is affecting not only the facility, but the span.

For more information about protection schemes, refer to the

Manage the Node

document.

Note

FP-LINK-LOSS

Default Severity: Minor (MN), Non-Service-Affecting (NSA)

Logical Object: EQPT

The Front Port Link Loss condition occurs when a LAN cable is not connected to the front port of the control
card.

Clear the FP-LINK-LOSS Condition

SUMMARY STEPS

1.

Connect a LAN cable to the front port of the control card.

DETAILED STEPS

Connect a LAN cable to the front port of the control card.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

FPGA-UPGRADE-FAILED

Default Severity: Critical (CR), Non-Service Affecting (NSA)

Logical Object: Equipment

The FPGA-UPGRADE-FAILED alarm is raised when the FPGA upgrade on the TNCS-2 or TNCS-2O control
card fails.

Clear the FPGA-UPGRADE-FAILED Alarm

Reboot the TNCS-2/TNCS-2O control card on the chassis.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

205

Alarm Troubleshooting

FP-LINK-LOSS

«
...
249
250
251
252
253
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: PaloAlto Networks Страницы: 3

Бренд: Watchguard Страницы: 39

Бренд: Paradyne Страницы: 112

Бренд: Cambium Networks Страницы: 215

Бренд: Falcon Страницы: 24

HHM Series HHM2411

Бренд: TDK Страницы: 2

Бренд: Jøtul Страницы: 20

Бренд: E-LINX Страницы: 24

Бренд: Z-Wave Страницы: 6

NVR41-4KS2 Series

Бренд: Dahua Страницы: 452

WISENET XRN-1610

Бренд: Hanwha Techwin Страницы: 88

Бренд: ADC Страницы: 29

Embedded Intelligent Module SX-560

Бренд: Silex technology Страницы: 110

Бренд: YDI Страницы: 16

Internet Security Appliances

Бренд: SonicWALL Страницы: 293

Бренд: Jabra Страницы: 2

Бренд: Vivotek Страницы: 185

Бренд: Allied Telesis Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды