Cisco NCS 2000 series Скачать руководство пользователя страница 539 | Manualshive

Страница: 539 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

CTC initialization has failed in the
specified step.

The CTC initialization failed during step {0}.

EID-2180

You must not include this link as it
originates from destination of a circuit.
It is against the path selection
algorithm.

This link cannot be included because it originates from
the destination.

EID-2181

The value of the specified item is
invalid.

The value of {0} is invalid.

EID-2182

Refer to the error message text.

The circuit roll failed. Bridge and roll is not supported
on VCAT circuits.

EID-2183

Refer to the error message text.

Spanning Tree Protocol cannot be enabled on some
ports because the ports have been assigned an
incompatible list of VLANs. You can view the
VLAN/Spanning Tree table or reassign the Ethernet
port VLANs.

EID-2184

Refer to the error message text.

The VLANs on some ports cannot be assigned because
they are incompatible with the Spanning Tree Protocol.
You can view the VLAN/Spanning Tree table or
reassign the VLANs.

EID-2185

The software could not be downloaded
onto the specified node.

The software download failed on node {0}.

EID-2186

You must shorten the length of the
ring name.

The ring name cannot exceed {0} characters. Please
try again.

EID-2187

The ring ID should not contain
alphanumeric characters, and must be
in the specified range.

The nodes in this ring do not support alphanumeric IDs.
Please use a ring ID between {0} and {1}.

EID-2188

Refer to the error message text.

The TL1 keyword "all" cannot be used as the ring name.
Please provide another name.

EID-2189

You have reached the maximum
number of nodes allowed.

Adding this span will cause the ring to contain more
nodes than allowed.

EID-2190

You must supply a ring name.

The ring name must not be empty.

EID-2191

CTC could not complete the circuit
creation request either because there
are no physical links, or the bandwidth
of the available links are already
reserved.

A valid route cannot be found for the circuit creation
request.

EID-2192

Refer to the error message text.

A valid route cannot be found for the circuit drop
creation request.

EID-2193

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

493

Error Messages

Error Messages Reference

«
...
537
538
539
540
541
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Ubiquiti Страницы: 24

Бренд: NEC Страницы: 47

Бренд: Abus Страницы: 60

Бренд: Farallon Страницы: 26

Бренд: Observint Страницы: 11

Бренд: Jetter Страницы: 35

RDX QuikStation 4

Бренд: Tandberg Data Страницы: 2

Бренд: XESS Страницы: 23

Бренд: Zhone Страницы: 7

Бренд: Zhone Страницы: 1

Бренд: Idis Страницы: 86

Бренд: Paradyne Страницы: 20

Бренд: Paradyne Страницы: 2

Бренд: Black Box Страницы: 9

Бренд: NETGEAR Страницы: 2

Бренд: UHP Страницы: 15

Бренд: Ubiquiti Страницы: 21

Бренд: Techroutes Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды