Cisco NCS 2000 series Скачать руководство пользователя страница 572 | Manualshive

Страница: 572 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

Refer to the error message text.

{0} does not support: - Low-order circuits that have
both {1}-protected and {2}-protected spans and that
cross a node that does not have low-order cross-connect
capability. - High-order circuits that carry low-order
circuits with the parameters described above.

EID-5082

During an RPR circuit creation ML
card, the new circuit size and the
existing circuit size must be the same.

This circuit is not the same size as the existing circuit
{0}. This circuit has size {1} and the existing circuit
has size {2}.

EID-5083

The trunk specified is not found.

The Trunk model could not be found. {0}

EID-5084

Refer to the error message.

The maximum number of VLAN DB profiles is {0}.

EID-5085

Refer to the error message.

The circuit roll failed. You cannot bridge and roll the
selected circuit because it has a monitor circuit.

EID-5086

Refer to the error message text.

You cannot use same slot for east working and west
protect ports.

EID-5087

Refer to the error message text.

You cannot use same slot for east working and west
protect ports.

EID-5088

Refer to the error message text

The maximum number of circuits that can be deleted
at a time is 200. Do you want to delete the first 200
circuits selected?

WID-5089

Refer to the error message text

This operation cannot be completed. The selected
circuits have different state models; please select
circuits of the same type.

EID-5090

Refer to the error message text

Some PPC terminations were not repaired.

EID-5091

Confirm if you really want to modify
TL1 tunnel encoding.

The TL1 encoding mode for the tunnel is being
changed. Do you want to modify the encoding?

WID-5092

Refer to the error message text.

Currently, CTC does not support bridge and roll on
circuits having multiple cross-connects on a single node.

EID-5094

Refer to the error message text.

No path were selected. Please select at least one path
starting from the {0} NE.

EID-5095

Refer to the error message text.

The first path must starts from the {0} NE.

EID-5096

Refer to the error message text.

The selected path should be linked with the last selected
and keep the same direction.

EID-5097

Refer to the error message text.

The node is not selectable. Only the Span between the
nodes are selectable.

EID-5098

Refer to the error message text.

Raman Command Error on {0}. {1}.

EID-5099

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

526

Error Messages

Error Messages Reference

«
...
570
571
572
573
574
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: GE Страницы: 6

Бренд: Rane Страницы: 4

neutrino series

Бренд: Xilica Audio Design Страницы: 26

Бренд: Dahua Страницы: 6

HAWA-Frontside 60/B

Бренд: hawa Страницы: 28

Бренд: Direct IP Страницы: 76

Бренд: H3C Страницы: 12

Бренд: Idis Страницы: 85

Бренд: Gemtek Systems Страницы: 51

Бренд: Kontron Страницы: 19

Бренд: RubyTech Страницы: 25

Бренд: ZyXEL Communications Страницы: 79

Бренд: ekwb Страницы: 11

Бренд: Alcatel-Lucent Страницы: 60

Бренд: Ruckus Wireless Страницы: 4

Бренд: Data Translation Страницы: 62

Edge-Core A07-ES4548C

Бренд: Atlantis Land Страницы: 2

Symphonique Strings SRX-04

Бренд: Roland Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды