Cisco NCS 2000 series Скачать руководство пользователя страница 293 | Manualshive

Страница: 293 / 602

background image

The KEY-EX-FAIL alarm is raised on the trunk port. However, there is no correlation with the OTN alarms
that are raised on the trunk.

Note

This alarm may be raised during these scenarios:

• A loss of signal on a fibre that may occur during key exchange. This results in failure of master key

exchange.

• Bit errors on the line during key exchange.

• Incorrect configuration of destination IP address, destination port or both in

Provisioning

>

Encryption

>

GCC2 Settings

in CTC.

• Card authentication enabled on one end and disabled on the other end.

Clearing the KEY-EX-FAIL Alarm

Before you begin

You must have Security user or Security super user privileges to clear the alarm.

Step 1

Ensure that there are no alarms on the client or trunk ports. This is because a loss of synchronization in the client port
may result in an AIS in the trunk port, which in turn cascades on the TLS.

Step 2

Reset the master key from CTC:

a) In node view (single shelf mode), or shelf view (multi-shelf mode), double-click the WSE card for which you want

to reset the master key.

b) Go to

Provisioning

>

Encryption

>

Key Management

.

c) Click the

Reset Master Key

button for the port to reset the master key.

d) Click

Apply

.

If the troubleshooting procedure does not clear the alarm, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

or call the Cisco Technical Assistance Center (1 800 553-2447) to

report the problem.

KEY-WRITE-FAIL

Default Severity: Major (MJ)

Logical Object: TRUNK (OTU)

The Key Write Failure alarm is raised on the OTU trunk port in the WSE card. This alarm is raised when the
programming of the key to the crypto FPGA fails.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

247

Alarm Troubleshooting

Clearing the KEY-EX-FAIL Alarm

«
...
291
292
293
294
295
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: ZETR Страницы: 2

Бренд: CallDirect Страницы: 33

Бренд: XMG Страницы: 5

Бренд: Habitat Страницы: 48

Бренд: NAD Страницы: 2

Бренд: Salus Страницы: 16

iW-RainboW-G30D

Бренд: iWave Страницы: 89

Бренд: Vivotek Страницы: 170

Wireless Mini PCI Module

Бренд: E-Tech Страницы: 42

Бренд: Allnet Страницы: 12

Бренд: Telebyte Страницы: 19

Wisenet PRN-6400B4

Бренд: Hanwha Techwin Страницы: 14

Бренд: ZALMAN Страницы: 9

InvenSense RoboKit1

Бренд: TDK Страницы: 13

Бренд: Galaxy Страницы: 30

Бренд: TRENDnet Страницы: 12

Bluespoon 17-1000

Бренд: Radio Shack Страницы: 1

Бренд: TP-Link Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды