manualshive.com logo in svg

Cisco NCS 2000 series, Руководство по устранению неисправностей

"Бесплатный Troubleshooting Manual для Cisco NCS 2000 series теперь доступен для скачивания с manualshive.com. Этот manual поможет вам настроить и обслуживать ваш продукт Cisco, обеспечивая стабильную работу сети. Загрузите его бесплатно прямо сейчас и узнайте все секреты работы с Cisco NCS 2000 series."

Поделиться
Скачать
background image

6.

If the fiber cable is properly connected and attached to the port, verify that the cable connects the card to
another Ethernet device and is not misconnected to an OC-N/STM-N card.

7.

If you are unable to establish connectivity, replace the fiber cable with a new known-good cable.

8.

If you are unable to establish connectivity, perform standard network or LAN diagnostics. For example,
trace the IP route, verify cable continuity, and troubleshoot any routers between the node and CTC. To
verify cable continuity, follow site practices.

DETAILED STEPS

Step 1

If the reporting card is an MXP or TXP card in an NCS node, verify the data rate configured on the PPM (also called
SFP):

a) In node view (single-shelf mode) or shelf view (multishelf mode), double-click the reporting MXP or TXP card.
b) Click the

Provisioning

>

Pluggable Port Modules

tabs.

c) View the Pluggable Port Modules area port listing in the

Actual Equipment Type

column and compare this with

the contents of the Selected PPM area Rate column for the MXP or TXP multirate port.

d) If the rate does not match the actual equipment, you must delete and recreate the selected PPM. Select the PPM (SFP),

click

Delete

, then click

Create

and choose the correct rate for the port rate.

For more information about provisioning PPMs (SFPs) and their specifications, refer to the

Installing the

GBIC, SFP, SFP+, and XFP Optical Modules in Cisco ONS Platforms

document.

Note

Step 2

If the reporting card is an OC-N/STM-N card, verify connectivity by pinging the system that is reporting the alarm.

Step 3

If the ping is successful, it demonstrates that an active TCP/IP connection exists. Restart CTC:

a) Exit from CTC.
b) Reopen the browser.
c) Log into CTC.

Step 4

Using optical test equipment, verify that proper receive levels are achieved. (For instructions about using optical test
equipment, refer to the manufacturer documentation.)

Always use the supplied electrostatic discharge wristband when working with a powered ONS system. Plug
the wristband cable into the ESD jack located on the lower-right edge of the shelf assembly.

Caution

Step 5

Verify that the optical LAN cable is properly connected and attached to the correct port.

Step 6

If the fiber cable is properly connected and attached to the port, verify that the cable connects the card to another Ethernet
device and is not misconnected to an OC-N/STM-N card.

Step 7

If you are unable to establish connectivity, replace the fiber cable with a new known-good cable.

Step 8

If you are unable to establish connectivity, perform standard network or LAN diagnostics. For example, trace the IP route,
verify cable continuity, and troubleshoot any routers between the node and CTC. To verify cable continuity, follow site
practices.

If the alarm does not get cleared, you need to report a Service-Affecting (SA) problem. Log into the Technical Support
Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or log into

http://www.cisco.com/c/

en/us/support/web/tsd-cisco-worldwide-contacts.html

to obtain a directory of toll-free Technical Support numbers for

your country.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

148

Alarm Troubleshooting

Clear the CARLOSS (EQPT) Alarm

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

NAIM AV2 Update Instructions preview
AV2
Бренд: NAIM Страницы: 2
Aztech DSL1000EW(L) Speci?Cations preview
DSL1000EW(L)
Бренд: Aztech Страницы: 2
Softing CAN-PRO1-PCIE Hardware User Manual preview
CAN-PRO1-PCIE
Бренд: Softing Страницы: 4
NAMCO SOUL CALIBUR II Manual preview
SOUL CALIBUR II
Бренд: NAMCO Страницы: 26
ZyXEL Communications PK5000Z How To Configure preview
PK5000Z
Бренд: ZyXEL Communications Страницы: 3
TP-Link TD-VG5612 Quick Installation Manual preview
TD-VG5612
Бренд: TP-Link Страницы: 2
ADTRAN EXPRESS 6503 User Manual preview
EXPRESS 6503
Бренд: ADTRAN Страницы: 20
Patton electronics ipRocketLink IAD 3086 Quick Start Manual preview
ipRocketLink IAD 3086
Бренд: Patton electronics Страницы: 12
Tripp Lite N002-025-GY Specification Sheet preview
N002-025-GY
Бренд: Tripp Lite Страницы: 3
A.E.B. ARCHIMEDE Fitting Instructions And Warranty Workbook preview
ARCHIMEDE
Бренд: A.E.B. Страницы: 28
Accton Technology Cheetah EtherCard-2320 Quick Installation Manual preview
Cheetah EtherCard-2320
Бренд: Accton Technology Страницы: 10
C&H Technologies EM405D100 Specification Sheet preview
EM405D100
Бренд: C&H Technologies Страницы: 2
Positron TeleLite 720920 Series Manual preview
TeleLite 720920 Series
Бренд: Positron Страницы: 21
Exsys EX-44354 Manual preview
EX-44354
Бренд: Exsys Страницы: 16
Paradyne FrameSaver DSL 9783 CSU/DSU User Manual preview
FrameSaver DSL 9783 CSU/DSU
Бренд: Paradyne Страницы: 233
Juniper EX8200 Series Brochure preview
EX8200 Series
Бренд: Juniper Страницы: 12
Billion BiPAC 7300GX Quick Start Manual preview
BiPAC 7300GX
Бренд: Billion Страницы: 8
Tripp Lite N308-05M Specification Sheet preview
N308-05M
Бренд: Tripp Lite Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды