Cisco NCS 2000 series Скачать руководство пользователя страница 275 | Manualshive

Страница: 275 / 602

background image

This alarm is demoted by a path label mismatch (PLM) such as LP-PLM.

By default, an HP-ENCAP-MISMATCH alarm causes an ML-Series card data link to go down. This behavior
can be modified using the command-line interface (CLI) command

no pos trigger defect encap

.

Note

Clear the HP-ENCAP-MISMATCH Alarm

SUMMARY STEPS

1.

Ensure that the correct framing mode is in use on the receiving card by completing the following steps:

2.

Ensure that the correct framing mode is in use on the transmit card, and that it is identical to the framing
mode used on the receiving card by completing the following steps:

3.

If the alarm does not clear, use the ML-Series card CLI to ensure that the remaining settings are correctly
configured:

DETAILED STEPS

Step 1

Ensure that the correct framing mode is in use on the receiving card by completing the following steps:

a) In node view, double-click the ML-Series card to display the card view.
b) Click the

Provisioning

>

Card

tabs.

c) In the Mode drop-down list, ensure that the correct mode (GFP-F or HDLC) is selected. If it is not, choose it and

click

Apply

.

Step 2

Ensure that the correct framing mode is in use on the transmit card, and that it is identical to the framing mode used on
the receiving card by completing the following steps:

a) In node view, double-click the ML-Series card to display the card view.
b) Click the

Provisioning

>

Card

tabs.

c) In the Mode drop-down list, ensure that the same mode (GFP-F or HDLC) is selected. If it is not, choose it and click

Apply

.

Step 3

If the alarm does not clear, use the ML-Series card CLI to ensure that the remaining settings are correctly configured:

• Encapsulation

• CRC size

• Scrambling state

To open the interface, click the card view

IOS

tab and click

Open IOS Connection

.

If the alarm does not get cleared, you need to report a Service-Affecting (SA) problem. Log into the Technical Support
Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or log into

http://www.cisco.com/c/

en/us/support/web/tsd-cisco-worldwide-contacts.html

to obtain a directory of toll-free Technical Support numbers for

your country.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

229

Alarm Troubleshooting

Clear the HP-ENCAP-MISMATCH Alarm

«
...
273
274
275
276
277
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Verizon DSL-2750B

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 10

Бренд: D-Link Страницы: 38

Бренд: Amperes Страницы: 8

Бренд: Alacritech Страницы: 20

Sure Cross DX70

Бренд: Banner Страницы: 35

Бренд: LevelOne Страницы: 31

Бренд: Lancom Страницы: 70

Бренд: Patton electronics Страницы: 12

Speedway Revolution

Бренд: impinj Страницы: 60

Converter Board R0E521237CFK00

Бренд: Renesas Страницы: 6

CNPS11X Extreme

Бренд: ZALMAN Страницы: 12

Бренд: JAKA Страницы: 37

H8S/2646 Series

Бренд: Renesas Страницы: 20

Бренд: Socket Страницы: 28

Бренд: Quatech Страницы: 98

Бренд: Alesis Страницы: 11

CyberPower RMCARD201

Бренд: CyberPower Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды