Cisco NCS 2000 series Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 602

background image

2.

Verify APC status:

3.

Verify that the intranode connections have been built in:

4.

Verify that all node connections have been created and that their state is Connected.

5.

If necessary, log into the Technical Support Website at http://www.cisco.com/techsupport for more
information or call Cisco TAC (1 800 553-2447) in order to report a service-affecting problem.

DETAILED STEPS

Step 1

Verify OSC connectivity:

a) Go to network view and identify the MSTP nodes to which the OCHNC circuit applies.
b) Verify that all the OSC links connecting the MSTP nodes along the circuit path, from the source node to the destination

node, are active (green line).

Bidirectional circuits have two possible nodes, depending on the line direction being considered.

Note

Complete one of the following actions depending on OSC connectivity:

• If the OSC link is down, focus on the affected span and troubleshoot the issue (see

System Restart after a Fiber

Cut, on page 65

).

If necessary, log into the Technical Support Website at http://www.cisco.com/techsupport for more
information or call Cisco TAC (1 800 553-2447) in order to report a service-affecting problem.

Note

• If the OSC link is not down, continue with

Corrective Action, on page 78

.

Step 2

Verify APC status:

a) Go to node view (single-shelf mode) or shelf view (multishelf mode) on the MSTP node that is the source node for

the circuit.

b) In the General Info box on the left, check the

APC state

(last row).

• If the APC state is DISABLE - INTERNAL, complete the appropriate troubleshooting procedure from

Troubleshooting, on page 99

.

If necessary, log into the Technical Support Website at http://www.cisco.com/techsupport for more
information or call Cisco TAC (1 800 553-2447) in order to report a service-affecting problem.

Note

• If the APC state is not DISABLE - INTERNAL, continue with Step 3.

Step 3

Verify that the intranode connections have been built in:

a) Go to the node view (single-shelf mode) or multishelf view (multishelf mode) on the MSTP node that is the source

node for the circuit.

b) Click the

Provisioning > WDM-ANS > Connections

tabs.

Step 4

Verify that all node connections have been created and that their state is Connected.

To quickly verify the connections, click the

Calculate Connection

button and check to see if any new

connections come up.

Tip

If some connections are missing, perform the proper procedure according to Turn Up a Node in the Configuration guide.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

79

General Troubleshooting

Corrective Action

«
...
123
124
125
126
127
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: 3Com Страницы: 48

Бренд: LAWO Страницы: 154

DR-4100P Series

Бренд: Idis Страницы: 30

WS-650 lite Series

Бренд: Laurell Страницы: 84

Бренд: 3Com Страницы: 16

Бренд: Fortinet Страницы: 20

Wisenet PRN-6400B4

Бренд: Hanwha Techwin Страницы: 14

Бренд: ZALMAN Страницы: 9

airHaul Nexus sB3010

Бренд: SmartBridges Страницы: 80

Бренд: Lattice Semiconductor Страницы: 43

ACCULINK 3161 CSU

Бренд: Paradyne Страницы: 19

Бренд: Keil Страницы: 68

netHOST NHST-T100

Бренд: hilscher Страницы: 75

IE-SW-VL09T-6TX-3SC

Бренд: Weidmuller Страницы: 14

Бренд: Dave Embedded Systems Страницы: 79

Бренд: LST Страницы: 1

Бренд: Planet Страницы: 66

Бренд: Manson Engineering Industrial Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды