Cisco NCS 2000 series Скачать руководство пользователя страница 530 | Manualshive

Страница: 530 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

There was an error during node
selection.

An error occurred during node selection.

EID-2024

Refer to the error or warning message
text. For example, this error is
generated from the node view
Provisioning> WDM-ANS> tabs to
indicate that the selected ring type is
not supported by the endpoints of the
circuit. Another example is the
Provisioning> VLAN tabs in card
view (Ethernet card only), where it
indicates that the back-end spanning
tree protocol (STP) disabling is not
supported.

This feature cannot be used. Verify that each endpoint
of this circuit is running software that supports this
feature.

EID-2025

Error occurred while attempting to
switch a path protection circuit away
from a span.

The {0} request could not be applied. {1}

EID-2026

CTC could not delete the circuit drop.

An error occurred while deleting the circuit drop.

EID-2027

CTC could not remove the circuit
node.

An error occurred while removing the circuit node.

EID-2028

The task you are trying to complete is
not supported by CTC.

The requested operation is not supported.

EID-2029

There was an error during
provisioning.

An error occurred during provisioning.

EID-2030

There was an error while adding a
node.

An error occurred while adding the node.

EID-2031

CTC could not rename the circuit.

The circuit could not be renamed. {0}

EID-2032

There was an internal error while
validating the user changes after the
Apply button was pressed. This error
can occur in the Edit Circuit dialog
box or in the BLSR table in the shelf
view (rare condition).

An error occurred during validation. {0}

EID-2033

Refer to the error message text.

Network circuits could not be added: {0}

EID-2034

Refer to the error message text.

The source and destination nodes are not connected.

EID-2035

You cannot delete the DCC/GCC link
as it is needed to access the node.

The {0} cannot be deleted. LAN Access has been
disabled on this node and this {0} is needed to access
the node.

EID-2036

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

484

Error Messages

Error Messages Reference

«
...
528
529
530
531
532
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Paradyne Страницы: 22

Бренд: Palo Alto Network Страницы: 56

SMART NODE 4950-NCE

Бренд: Patton electronics Страницы: 8

NetLink 2960 RAS

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 2

Бренд: Commell Страницы: 58

Бренд: Vonets Страницы: 8

Бренд: Lanner electronics Страницы: 59

WGR614 - Wireless-G Router Wireless

Бренд: NETGEAR Страницы: 116

ADSL Ethernet & USB Combo Router Lynx L-510

Бренд: Starbridge Networks Страницы: 59

IE-SW-VL09T-6TX-3SC

Бренд: Weidmuller Страницы: 14

Бренд: Digital Audio Corporation Страницы: 164

Бренд: ExtraHop Страницы: 3

Protection Board R0E330850ACBP0

Бренд: Renesas Страницы: 8

Бренд: Alcatel Страницы: 158

Бренд: BenQ Страницы: 38

WIRELESS-G CARDBUS PC CARD - GUIDE D

Бренд: Hawking Страницы: 26

Бренд: ICS Advent Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды