Cisco NCS 2000 series Скачать руководство пользователя страница 305 | Manualshive

Страница: 305 / 602

background image

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

LMP-UNALLOC

Default Severity: Not Alarmed (NA), Non-Service-Affecting (NSA)

Logical Object: GE

The LMP Data Link Unallocated condition is raised when the control card receives an LMP link summary or
channel status message reporting that the data link as unallocated for data traffic. The condition clears when
the data link is allocated and sends an LMP link summary or channel status message to this effect. If a data
link has the LMP-UNALLOC alarm raised against it, this should suppress all other alarms on the client port,
since the far-end node is not using the errored port. (Consequently you do not have to clear any alarms on the
far-end node unused port.)

LMP-UNALLOC is part of an alarm hierarchy that includes

LMP-SD, on page 256

, and

LMP-SF, on page

. The hierarchy is as follows: If LMP-UNALLOC is raised, LMP-SF and LMP-SD are suppressed. If

LMP-SF is raised, it suppresses LMP-SD. LMP-SF and LMP-UNALLOC both suppress near-end LOS-type
DWDM client alarms, but LMP-SD does not.

In most cases, this condition is an informational notice at the near-end node that the far-end port is not being
utilized. If, however, the far-end port should be allocated for traffic, log into the Technical Support Website
at

http://www.cisco.com/cisco/web/support/index.html

for more information or call Cisco TAC (1 800

553-2447)..

LOCAL-CERT-CHAIN-VERIFICATION-FAILED

Default Severity: Major (MJ), Non-Service-Affecting (NSA)

Logical Object: EQPT

The Local Certificate Chain Verification Failed alarm is raised when the verification of an active certificate
chain in the card fails.

Clear the LOCAL-CERT-CHAIN-VERIFICATION-FAILED Alarm

This alarm is cleared when the verification of an active certificate chain in the card is pass.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

259

Alarm Troubleshooting

LMP-UNALLOC

«
...
303
304
305
306
307
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Express EtherNetwork DFE-670TXD

Бренд: D-Link Страницы: 4

Бренд: DAD Страницы: 36

Бренд: D-Link Страницы: 2

Бренд: F5 Страницы: 2

Бренд: F5 Страницы: 90

Бренд: F5 Страницы: 47

HBJC924R3288DG2NS Series

Бренд: JETWAY Страницы: 6

Бренд: ZyXEL Communications Страницы: 422

Бренд: XJTAG Страницы: 9

Бренд: Xilinx Страницы: 8

Бренд: Lantech Страницы: 40

DEEP LEARNING PLUS

Бренд: Concept Pro Страницы: 28

CyberSWITCH CSX101

Бренд: Cabletron Systems Страницы: 72

Бренд: B+B SmartWorx Страницы: 50

Бренд: Cradlepoint Страницы: 2

Бренд: Hawking Страницы: 21

TGXPS-1080-M12-MV Series

Бренд: ORiNG Страницы: 2

Tamar FCSAS102800

Бренд: Bridgeworks Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды