Cisco NCS 2000 series Скачать руководство пользователя страница 600

Страница: 600 / 602

Description

Error/Warning Message

Error/Warning
ID

Interface is already created or wrong
parameters configured.

UNI Wrong Configuration.\n {0}

EID-6626

Performing an unsupported operation.

The operation is not supported

EID-6627

LAN WAN is enabled on the Port.

LAN WAN Enabled on the Port.

EID-6628

The PPM does not have any mode
provisioned. Create a card mode for
the ports before creating the payload.

Operating mode is not provisioned on the PPM.

EID-6629

FEC mode is not configured correctly
for the protection mode being
provisioned during circuit creation.

The FEC settings are incompatible.

EID-6630

Valid licence is not installed on the
peer card for the operation mode being
provisioned.

Operation is not Supported. Valid License is not
available on Card/Peer Combination.

EID-6631

The following table lists the error messages for RAMAN-CTP, RAMAN-COP, EDRA-1-xx, and EDRA-2-xx
cards.

Cause/Solution

Error Message

Error

If the condition does not clear, log
into the Technical Support Website
at

http://www.cisco.com/c/en/us/

support/index.html

for more

information or call Cisco TAC (1
800 553-2447).

Unexpected internal Error

Error RC01

Ensure the Raman card is properly
plugged in and is active.

Raman card is not plugged or not
ACTIVE

Error RC02

Check for fiber continuity and
connectors.

Raman pumps are not ON (either
OFF or APR)

Error RC03

Ensure ANS parameters are
properly set by ANS.

Target Raman Gain/Tilt not set by
ANS

Error RC04

The OSC PPP is down or there is
no communication between nodes.

No reply received from facing node
(nodes communication error)

Error RC05

Check if an OTDR scan is running
from either end of span or a Raman
calibration is under progress

Cards in facing node are missing
or busy - in use by another
calibration or OTDR scan running

Error RC06

Raman Card is busy - in use by
another calibration (another side in
this node) or OTDR scan running

Error RC07

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

554

Error Messages

Error Messages Reference

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание NCS 2000 series

Отзывы:

Похожие инструкции для NCS 2000 series

Бренды по названию

Популярные бренды

Cisco NCS 2000 series, Руководство по устранению неисправностей

Результаты поиска

Содержание NCS 2000 series

Отзывы:

Похожие инструкции для NCS 2000 series

Бренды по названию

Популярные бренды