Cisco NCS 2000 series Скачать руководство пользователя страница 555 | Manualshive

Страница: 555 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

The absolute value entered was wrong.

An ordering error occurred. The absolute value should
be {0}.

EID-3247

CTC changed the incorrect parameter.

The value for the parameter {0} is invalid.

EID-3248

Refer to the error message text.

The voltage increment value is invalid.

EID-3249

Refer to the error message text.

The power monitor range is invalid.

EID-3250

CTC could not complete the specified
action.

The requested action could not be completed. {0}

EID-3251

Refer to the error message text.

No download has been initiated from this CTC session.

EID-3252

Refer to the error message text.

The reboot operation failed. {0}

EID-3253

The Cisco Transport Controller (CTC)
was unable to validate the values
entered by the user, specified by {0}.
This error message is common to
several different provisioning tabs
within the CTC.

An error occurred during validation. {0}

EID-3254

Refer to the error message text.

You cannot change the timing configuration because a
Manual/Force operation is in effect.

EID-3255

Refer to the warning message text.

The timing reference(s) could not be assigned because
one or more of the timing reference(s): - is already used
and/or - has been selected twice and/or - is attempting
to use the same slot twice. Please verify the settings.

WID-3256

CTC detected more than one
occurrence of the a DCC number.
Remove one of them.

Duplicate DCC numbers are not permitted. {0}.

EID-3257

Refer to the error message text.

A software error occurred while attempting to download
the file. Please try again later.

EID-3258

You must create a Fibre Channel
Multirate (FC_MR) card threshold.

An error occurred while creating the FC-MR threshold.

EID-3259

The specified internal subnet could not
be provisoned.

An error occurred while provisioning the internal
subnet: {0}

EID-3260

Refer to the error message text.

The port rate provisioning cannot be changed while
circuits exist on this port.

EID-3261

You must provision the ports only
when the port is Out of Service.

The port provisioning cannot be changed when the port
status is {0}.

EID-3262

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

509

Error Messages

Error Messages Reference

«
...
553
554
555
556
557
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Professional Series

Бренд: PACOM Страницы: 15

Бренд: Idis Страницы: 123

Бренд: Idis Страницы: 29

Бренд: Idis Страницы: 28

DirectIP DR-1304P

Бренд: Idis Страницы: 82

Бренд: iDirect Страницы: 130

DR-4100P Series

Бренд: Idis Страницы: 30

Бренд: Zonet Страницы: 8

Бренд: D-Link Страницы: 83

Бренд: STONEFLY Страницы: 48

OCTOPUS 5TX-EEC

Бренд: Hirschmann Страницы: 6

Бренд: ICP DAS USA Страницы: 8

HHM Series HHM2245SA1

Бренд: TDK Страницы: 2

Бренд: Lutron Electronics Страницы: 4

Бренд: IBM Страницы: 34

Бренд: Nortel Страницы: 163

Бренд: Baracoda Страницы: 16

Бренд: Compal Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды