Cisco NCS 2000 series Скачать руководство пользователя страница 262 | Manualshive

Страница: 262 / 602

background image

Clear the GFP-CSF-SYNCLOSS Alarm

SUMMARY STEPS

1.

Clear the Service-Affecting (SA) alarm at the remote data port.

DETAILED STEPS

Clear the Service-Affecting (SA) alarm at the remote data port.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

GFP-LFD

Default Severity: Major (MJ), Service-Affecting (SA)

Logical Object: CEMR, CE1000, CE100T, FCMR, GFP-FAC, ML1000, ML100T, MLFX

The GFP Loss of Frame Delineation alarm applies to Fibre Channel, FICON GFP, and Ethernet ports. This
alarm occurs if there is a faulty SONET connection, if SONET path errors cause GFP header errors in the
check sum calculated over payload length (PLI/cHEC) combination, or if the GFP source port sends an invalid
PLI/cHEC combination. This loss causes traffic stoppage.

Clear the GFP-LFD Alarm

SUMMARY STEPS

1.

Look for and clear any associated SONET path errors such as LOS or the

AU-AIS, on page 129

alarm that

originate at the transmit node.

DETAILED STEPS

Look for and clear any associated SONET path errors such as LOS or the

AU-AIS, on page 129

alarm that originate at

the transmit node.

If the alarm does not get cleared, you need to report a Service-Affecting (SA) problem. Log into the Technical Support
Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or log into

http://www.cisco.com/c/

en/us/support/web/tsd-cisco-worldwide-contacts.html

to obtain a directory of toll-free Technical Support numbers for

your country.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

216

Alarm Troubleshooting

Clear the GFP-CSF-SYNCLOSS Alarm

«
...
260
261
262
263
264
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Mackie Страницы: 2

Бренд: Mackie Страницы: 5

Бренд: Belkin Страницы: 72

Бренд: Helmholz Страницы: 28

Kinetic FLT 80 D5/DDC Body

Бренд: EK-Quantum Страницы: 16

Бренд: ZALMAN Страницы: 9

Бренд: T.A Страницы: 11

Бренд: Rosewill Страницы: 3

Бренд: EVOC Страницы: 57

Бренд: Hama Страницы: 25

Бренд: Infoblox Страницы: 16

Бренд: Cypress Semiconductor Страницы: 19

Бренд: MA lighting Страницы: 49

NVR2104/2108HS-W-4KS2 1U

Бренд: Dahua Technology Страницы: 363

Бренд: Z3 Technology Страницы: 22

Бренд: H3C Страницы: 103

Бренд: Extreme Networks Страницы: 51

Бренд: LevelOne Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды