Cisco NCS 2000 series Скачать руководство пользователя страница 242 | Manualshive

Страница: 242 / 602

background image

h)

Click the

Provisioning

>

Port

>

General

tabs.

i)

Under Admin State, click the cell and choose

IS

(or

Unlocked

).

j)

Click

Apply

.

Step 3

Program the Credits Available value based on the buffers available on the connected equipment by completing the
following steps:

The NumCredits entry must be provisioned to a value smaller than or equal to the receive buffers or credits
available on the connected equipment.

Note

a) Double-click the card.
b) Click the

Provisioning

>

Port

>

Distance Extension

tabs.

c) Enter a new value in the Credits Available column.
d) Click

Apply

.

If the alarm does not get cleared, you need to report a Service-Affecting (SA) problem. Log into the Technical Support
Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or log into

http://www.cisco.com/c/

en/us/support/web/tsd-cisco-worldwide-contacts.html

to obtain a directory of toll-free Technical Support numbers for

your country.

FDI

Default Severity: Not Alarmed (NA), Non-Service-Affecting (NSA)

Logical Objects: OCH, OCH-TERM, OMS, OTS, EQPT

The Forward Defect Indication (FDI) condition is part of network-level alarm correlation. It is raised at the
far end when the OCH optical payload is missing due to an optical channel signal (LOS), light (LOS-P), or
optical power (OPWR-LFAIL) alarm root cause.

An LOS, LOS-P, or OPWR-LFAIL alarm on a circuit causes multiple alarms for each channel. Correlation
simplifies troubleshooting by reporting a single alarm for multiple alarms having one root cause, then demoting
the root alarms so that they are only visible in the Conditions window (showing their original severity.)

FDI clears when the optical channel is working on the aggregated or single-channel optical port.

Network-level alarm correlation is only supported for communication alarms. It is not supported for equipment
alarms.

Note

Clear the FDI Condition

SUMMARY STEPS

1.

Clear the root-cause service-affecting alarm by using one of the following procedures, as appropriate:

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

196

Alarm Troubleshooting

FDI

«
...
240
241
242
243
244
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: H3C Страницы: 1057

Бренд: WAGO Страницы: 2

Бренд: Draytek Страницы: 8

Бренд: STONEFLY Страницы: 48

Бренд: FOR-A Страницы: 72

TWR-SB0410-36EVB

Бренд: NXP Semiconductors Страницы: 26

Бренд: Rolls Страницы: 1

Бренд: Alcatel-Lucent Страницы: 60

Digital Loudspeaker

Бренд: Dolby Laboratories Страницы: 4

Бренд: ZyXEL Communications Страницы: 12

Бренд: N-Tron Страницы: 2

Бренд: DOD Страницы: 12

Бренд: Alpine Страницы: 17

Бренд: Hamlet Страницы: 6

Selenio SNP-GW-3GX32

Бренд: Imagine communications Страницы: 153

Бренд: Transition Networks Страницы: 5

Бренд: Planet Страницы: 136

FusionHDTV 5 GOLD

Бренд: Dvico Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды