Cisco NCS 2000 series Скачать руководство пользователя страница 551 | Manualshive

Страница: 551 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

Refer to the error message text.

Probable causes: - Unable to switch, because a similar
or higher priority condition exists on a peer or far-end
card. - A loopback is present on the working port. -
Protect port is in OOS disabled admin state

EID-3158

CTC encountered an error while
applying this operation.

EID-3159 can appear if you attempt
to perform another switching operation
within a certain time interval. This
interval is an algorithm of three
seconds per working card in the
protection group. The maximum
interval is 10 seconds.

An error occurred while applying the operation.

EID-3159

CTC encountered the specified error.

An error occurred while provisioning the {0}.

EID-3160

An error was encountered while
attempting to upgrade the BLSR.
Refer to the details portion of the error
dialog box for more information.

An error occurred while upgrading the ring.

EID-3161

Refer to the error message text.

This protection operation cannot be set because the
protection operation on the other side has been changed
but not yet applied.

EID-3162

CTC cannot validate the data for the
specified row.

The data in row {0} cannot be validated.

EID-3163

The new specified node ID for the
specified ring ID is the same as
another node ID.

The new node ID ({0}) for ring ID {1} duplicates the
ID of node {2}.

EID-3164

Refer to the error message text.

The ring ID provided is already in use. Ring IDs must
be unique.

EID-3165

CTC encountered an error while
refreshing the specified table.

An error occurred while refreshing the {0} table.

EID-3166

Refer to the error message text.

The slot is already in use.

EID-3167

An error was encountered while
attempting the specified provisioning
operation. Refer to the details portion
of the error dialog box for more
information.

An error occurred while provisioning.

EID-3168

CTC encountered an error while
adding the card.

An error occurred while adding the card.

EID-3169

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

505

Error Messages

Error Messages Reference

«
...
549
550
551
552
553
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Abus Страницы: 60

MatrixPRO-II DVI 16x16

Бренд: Barco Страницы: 43

Бренд: Barco Страницы: 5

DR-4100P Series

Бренд: Idis Страницы: 30

Бренд: A10 Страницы: 52

HiGain HLU-231 List 8F

Бренд: ADC Страницы: 7

Бренд: FS Страницы: 19

Бренд: Allied Telesis Страницы: 1

Бренд: iBall Baton Страницы: 9

RUGGEDMAX WIN7000

Бренд: RuggedCom Страницы: 42

Бренд: Accom Страницы: 15

Aquaduct 360 XT

Бренд: Aqua Computer Страницы: 28

ELC-LTTR240-TBP

Бренд: ENERMAX Страницы: 16

Super Sound Set SR-JV80-07

Бренд: Roland Страницы: 8

Бренд: Schrack Technik Страницы: 2

Бренд: UfiSpace Страницы: 34

Бренд: WABCO Страницы: 29

Бренд: Rockwell Automation Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды