manualshive.com logo in svg
background image

FORBIDDEN BY INTERNATIONAL LAW TO DUPLICATE OR TO DISTRIBUTE TO UNAUTHORIZED PERSONS OR PARTIES WITHOUT PRIOR WRITTEN 

PERMISSION FROM ACCOM, INCORPORATED. 

 

Installation Procedure

 

05 November, 2004 

Digital Audio Option

 

Copyright © 2004 / Accom, Incorporated

 

Background 

This procedure describes the process required to install the Digital Audio Option into an existing WSD/HDe Digital Disk Recorder. Only 
qualified technical personnel should perform this installation procedure. 

This installation procedure requires you to remove the WSD/HDe chassis from the equipment rack (if it is rack-mounted). The entire 
installation procedure should take less than an hour (60 minutes) to perform, including removal of the WSD/HDe chassis from an 
equipment rack. If the WSD/HDe is not rack mounted, the procedure should take less than 30 minutes to perform. 

It is strongly advised for you to first read over this entire document before beginning this procedure, to make sure you understand the task 
you are about to perform. If you have any questions about or difficulty in performing this procedure, contact Accom Technical Support 
between the hours of 8:00am and 4:00pm Pacific Standard Time (PST) at +1-650-328-3818. Or e-mail J. Vyas at [email protected]  

Parts Included 

The Digital Audio Option Installation Kit includes the following items: 

 

(1) PCI Board / Digital Audio 8-Track 

Accom Part Number 9400-0920-01 

 

(2) Cable Assembly / 20-Pin Mini Ribbon 

Accom Part Number 9000-0776-00 

 

(1) Cable Assembly / 26-Pin-D Digital Audio 

Accom Part Number 9000-0741-00 

 

(1) Adaptec SCSI RAID Controller 2100S 

Accom Part Number 2500-0335 

 

(1) Audio Breakout Panel 

Accom Part Number 9500-0328-00 

 

(2) Audio Breakout Panel / Leg Stand 

Accom Part Number 8900-1406-00 

 

(2) Audio Breakout Panel / Rack Ears 

Accom Part Number 8900-1407-00 

 

(4) Rubber Foot 

Accom Part Number 1901-0441 

 

(4) Philips-Head Screws / 6-32 x 1/4” 

Accom Part Number 1901-0251 

 

(14) Philips-Head Screws / 6-32 x 3/16” 

(12) screws are required for retrofit; (2) are extra 
Accom Part Number 1901-6328 

 

(4) Label / WSD-HD Options 

Accom Part Number 8901-1252-01 

 

(2) SCSI Disk Drive / 18GB or 36GB or 73GB 

Accom Part Number 1600-0148 for 18GB; -0149 for 36GB; -0146 for 73GB 

Tools Required 

The following tools are required to perform this installation: 

 

Philips-Head Screw Driver / Large Size 

 

Philips-Head Screw Driver / Medium Size 

Continued on next page… 

Document Revised: 5-Nov-04 @ 8:09 AM 

©

2004 / Accom, Incorporated 

Page 1 of 15 

Содержание WSD/HDe
















Отзывы: