Cisco NCS 2000 series Скачать руководство пользователя страница 196 | Manualshive

Страница: 196 / 602

background image

3.

If there is no fiber cut or provisioning error, check the client-side equipment for any transmission errors
on the line.

DETAILED STEPS

Step 1

Ensure that the GE client is correctly configured:

a) In node view (single-shelf mode) or shelf view (multishelf mode), double-click the card to open the card view.
b) Click the

Provisioning

>

Pluggable Port Modules

tabs.

c) View the Pluggable Port Modules area port listing in the

Actual Equipment Type

column and compare this with

the client equipment. If no PPM (SFP) is provisioned, refer to the Turn Up a Node chapter. PPM (SFP) specifications
are listed in the

Installing the GBIC, SFP, SFP+, and XFP Optical Modules in Cisco ONS Platforms

document.

d) If a PPM (SFP) has been created, view the contents of the Selected PPM area Rate column for the MXP or TXP MR

card and compare this rate with the client equipment data rate. In this case, the rate should be ONE_GE or 10G
Ethernet. If the PPM (SFP) rate is differently provisioned, select the PPM (SFP), click

Delete

, then click

Create

and

choose the correct rate for the equipment type.

For information about installing and provisioning PPMs (SFPs), refer to the

Installing the GBIC, SFP,

SFP+, and XFP Optical Modules in Cisco ONS Platforms

document.

Note

Step 2

If there is no PPM (SFP) misprovisioning, check for a fiber cut. An LOS alarm would also be present. If there is an alarm,
complete the Clear the LOS (OCN/STMN) Alarm procedure located in Chapter 2, Alarm Troubleshooting, of the
Troubleshooting guide.

Step 3

If there is no fiber cut or provisioning error, check the client-side equipment for any transmission errors on the line.

If the alarm does not get cleared, you need to report a Service-Affecting (SA) problem. Log into the Technical Support
Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or log into

http://www.cisco.com/c/

en/us/support/web/tsd-cisco-worldwide-contacts.html

to obtain a directory of toll-free Technical Support numbers for

your country.

CARLOSS (ISC)

Default Severity: Major (MJ), Service-Affecting (SA)

Logical Object: ISC

The Carrier Loss for Inter-Service Channel (ISC) alarm occurs on:

• The client port of a TXP_MR_10G, TXP_MR_10E, TXP_MR_10E_C, TXP_MR_10E_L, TXP_MR_2.5G,

TXPP_MR_2.5G, MXP_MR_2.5G, or MXPP_MR_2.5G card supporting ISC traffic.

• Ports of the MS-ISC card when the NCS is configured as an NC shelf.

• MSM ports of an NCS NC shelf.

• MSM ports of an NCS SS shelf.

The loss can be due to a misconfiguration, fiber cut, or client equipment problem.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

150

Alarm Troubleshooting

CARLOSS (ISC)

«
...
194
195
196
197
198
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Xantrex Страницы: 8

Бренд: FabiaTech Страницы: 4

Бренд: Lab.gruppen Страницы: 35

Бренд: Yaesu Страницы: 2

StorageWorks AIT 35GB AutoLoader

Бренд: Compaq Страницы: 4

HHM Series HHM2411

Бренд: TDK Страницы: 2

Бренд: M86 Security Страницы: 309

Digital Encoder Plus

Бренд: IDT Страницы: 98

Бренд: AMX Страницы: 2

DiamondLink 3201

Бренд: Patton Страницы: 12

Ezi-SERVOII EtherCAT TO

Бренд: Fastech Страницы: 108

Бренд: Global411 Страницы: 15

PowerMatch ESPLink

Бренд: Bose Страницы: 2

DEEP LEARNING PLUS

Бренд: Concept Pro Страницы: 28

Бренд: Airlinkplus Страницы: 20

Бренд: Ista Страницы: 16

Бренд: Sierra Wireless Страницы: 2

Бренд: Acromag Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды