Cisco NCS 2000 series Скачать руководство пользователя страница 96

Страница: 96 / 602

Step 8

Again, click the New button under the System variables field.

Step 9

Type

CTC_MAX_PERM_SIZE_HEAP

in the Variable Name field.

Step 10

Type

256

in the Variable Value field, and then click the

button to create the variable.

Step 11

Click the

button in the Environment Variables window to accept the changes.

Step 12

Click the

button in the System Properties window to accept the changes.

Set the CTC_HEAP and CTC_MAX_PERM_SIZE_HEAP Environment Variables for Solaris

SUMMARY STEPS

From the user shell window, kill any CTC sessions and browser applications.

In the user shell window, set the environment variables to increase the heap size.

DETAILED STEPS

Step 1

From the user shell window, kill any CTC sessions and browser applications.

Step 2

In the user shell window, set the environment variables to increase the heap size.

Example:

The following example shows how to set the environment variables in the C shell:

% setenv CTC_HEAP 896
% setenv CTC_MAX_PERM_SIZE_HEAP 256

Browser Stalls When Downloading CTC JAR Files From Control Card

Problem

The browser stalls or hangs when downloading a CTC Java archive (JAR) file from the control card.

Possible Cause

McAfee VirusScan software might be interfering with the operation. The problem occurs

when the VirusScan Download Scan is enabled on McAfee VirusScan 4.5 or later.

Solution

Disable the VirusScan Download Scan feature. Complete the

Disable the VirusScan Download Scan,

on page 50

Disable the VirusScan Download Scan

SUMMARY STEPS

From the Windows Start menu, choose

Programs > Network Associates > VirusScan

Console.

Double-click the

VShield

icon listed in the VirusScan Console dialog box.

Click

Configure

on the lower part of the Task Properties window.

Click the

Download Scan

icon on the left of the System Scan Properties dialog box.

Uncheck the

Enable Internet download

scanning check box.

Click

Yes

when the warning message appears.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

General Troubleshooting

Set the CTC_HEAP and CTC_MAX_PERM_SIZE_HEAP Environment Variables for Solaris

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание NCS 2000 series

Отзывы:

Похожие инструкции для NCS 2000 series

Бренды по названию

Популярные бренды

Cisco NCS 2000 series, Руководство по устранению неисправностей

Результаты поиска

Содержание NCS 2000 series

Отзывы:

Похожие инструкции для NCS 2000 series

Бренды по названию

Популярные бренды