Cisco NCS 2000 series Скачать руководство пользователя страница 355 | Manualshive

Страница: 355 / 602

background image

Clear the MS-RFI Condition

SUMMARY STEPS

1.

Log into the far-end node of the reporting NCS.

2.

Determine whether there are other alarms, especially the LOS(STM1E, STMN).

3.

Clear the main alarm. See the appropriate alarm section in this chapter for the procedure.

DETAILED STEPS

Step 1

Log into the far-end node of the reporting NCS.

Step 2

Determine whether there are other alarms, especially the LOS(STM1E, STMN).

Step 3

Clear the main alarm. See the appropriate alarm section in this chapter for the procedure.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

MT-OCHNC

Default Severity: Not Alarmed (NA), Non-Service-Affecting (NSA)

Logical Object: OTS

The MT-OCHNC condition occurs when the user provisions (tunes) a specific wavelength for maintenance
on a WXC card from an input port (EXP1-8, ADD-RX) to the output port (COM-TX).

Clear the MT-OCHNC Condition

SUMMARY STEPS

1.

Delete the provisioned wavelength that was specifically tuned for maintenance purposes on a WXC card.

DETAILED STEPS

Delete the provisioned wavelength that was specifically tuned for maintenance purposes on a WXC card.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

NO-SHARED-CIPHERS Alarm

Default Severity: Major (MJ), Service Affecting (SA)

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

309

Alarm Troubleshooting

Clear the MS-RFI Condition

«
...
353
354
355
356
357
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

C50FSi - VB Network Camera

Бренд: Canon Страницы: 32

Бренд: Rabbit Страницы: 120

Бренд: Jetter Страницы: 35

Бренд: REXROTH Страницы: 68

Бренд: Alesis Страницы: 46

RUGGEDSWITCH RS900G

Бренд: RuggedCom Страницы: 23

DG834GT - 108 Mbps Super G Wireless ADSL Router

Бренд: NETGEAR Страницы: 2

Бренд: Patton electronics Страницы: 13

Бренд: Angel Cool Страницы: 2

OMB-DAQBOARD-500 Series

Бренд: Omega Страницы: 48

Бренд: FOR-A Страницы: 2

Бренд: Supermicro Страницы: 15

Бренд: Promise Technology Страницы: 26

Бренд: Solwise Страницы: 231

Бренд: ZiLOG Страницы: 317

Бренд: Paradyne Страницы: 74

Бренд: Taiwan Commate Computer Inc. Страницы: 25

Бренд: Greenlee Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды