Cisco NCS 2000 series Скачать руководство пользователя страница 443 | Manualshive

Страница: 443 / 602

background image

DETAILED STEPS

Step 1

Ensure that the port connection at the near end of the SONET or SDH (ETSI) link is operational.

Step 2

Verify fiber continuity to the port. To verify fiber continuity, follow site practices.

Step 3

Check the physical port LED on the card. The port LED looks clear (that is, not lit green) if the link is not connected.

If the alarm does not get cleared, you need to report a Service-Affecting (SA) problem. Log into the Technical Support
Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or log into

http://www.cisco.com/c/

en/us/support/web/tsd-cisco-worldwide-contacts.html

to obtain a directory of toll-free Technical Support numbers for

your country.

SNTP-HOST

Default Severity: Minor (MN), Non-Service-Affecting (NSA)

Logical Object: NE

The Simple Network Timing Protocol (SNTP) Host Failure alarm indicates that an NCS system serving as
an IP proxy for the other NCS system nodes in the ring is not forwarding SNTP information to the other nodes
in the network. The forwarding failure can result from two causes: either the IP network attached to the NCS
system proxy node is experiencing problems, or the NCS system proxy node itself is not functioning properly.

Clear the SNTP-HOST Alarm

SUMMARY STEPS

1.

Ping the SNTP host from a workstation in the same subnet to ensure that communication is possible within
the subnet by completing the

Verify PC Connection to the NCS (ping), on page 45

procedure.

2.

If the ping fails, contact the network administrator who manages the IP network that supplies the SNTP
information to the proxy and determine whether the network is experiencing problems, which could affect
the SNTP server/router connecting to the proxy system.

3.

If no network problems exist, ensure that the NCS system proxy is provisioned correctly:

4.

If proxy is correctly provisioned, refer to the Timing chapter in the Configuration guide for more
information on SNTP Host.

DETAILED STEPS

Step 1

Ping the SNTP host from a workstation in the same subnet to ensure that communication is possible within the subnet
by completing the

Verify PC Connection to the NCS (ping), on page 45

procedure.

Step 2

If the ping fails, contact the network administrator who manages the IP network that supplies the SNTP information to
the proxy and determine whether the network is experiencing problems, which could affect the SNTP server/router
connecting to the proxy system.

Step 3

If no network problems exist, ensure that the NCS system proxy is provisioned correctly:

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

397

Alarm Troubleshooting

SNTP-HOST

«
...
441
442
443
444
445
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Accelerated Страницы: 10

Бренд: Accelerated Страницы: 4

Бренд: Linksys Страницы: 2

DHI-NVR5224-24P-4KS2

Бренд: Dahua Страницы: 24

Бренд: Yamaha Страницы: 4

Бренд: Laird Страницы: 36

Adapter Bracket

Бренд: Paradyne Страницы: 1

Бренд: Quectel Страницы: 23

Бренд: Bridgeworks Страницы: 18

Бренд: SUNRICH TECHNOLOGY Страницы: 5

Бренд: Cromemco Страницы: 46

Бренд: Verizon Wireless Страницы: 39

Бренд: FONESTAR Страницы: 8

Бренд: Renesas Страницы: 2

NIC-FC730i-Mb-2-32G

Бренд: H3C Страницы: 37

Бренд: Omron Страницы: 13

Elinx EIR510 Series

Бренд: B&B Electronics Страницы: 2

Бренд: Casablanca Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды