Cisco NCS 2000 series Скачать руководство пользователя страница 526 | Manualshive

Страница: 526 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

Refer to the error message text.

The host name of the network element cannot be
resolved to an address.

EID-1000

Refer to the error message text.

Unable to launch CTC due to applet security
restrictions.

Please review the installation instructions to make sure
that the CTC launcher is given the permissions it needs.

Note that you must exit and restart your browser in
order for the new permissions to take effect.

EID-1001

The node is not reachable from CTC
client station.

The host name (e.g., for the network element) was
successfully resolved to its address, but no route can
be found through the network to reach the address.

EID-1002

Unexpected exception or error while
launching CTC from the applet.

An error was encountered while attempting to launch
CTC. {0}

EID-1003

Unable to delete the CTC cached
JARs, because another application
may have the JAR files running; for
example, another instance of CTC.

Problem Deleting CTC Cache: {0} {1}

EID-1004

CTC encountered an error while
writing to log files, preference files,
etc.

An error occurred while writing to the {0} file.

EID-1005

The URL used to download the
specified JAR file is incorrect.

The URL used to download {0} is malformed.

EID-1006

An input or output exception was
encountered when CTC tried to
download the specified JAR file.

An I/O error occurred while trying to download {0}.

EID-1007

The password is invalid.

Password shall not contain the associated user-ID.

EID-1018

CTC could not create the file due to
an invalid filename.

Could not create {0}. Please enter another filename.

EID-1019

CTC was unable to switch from the
node or card view to the network view
and is now shutting down.

Fatal exception occurred, exiting CTC. Unable to switch
to the Network view.

EID-1020

CTC was unable to display the
requested view (node or network).

Unable to navigate to {0}.

EID-1021

Refer to the error message text.

An IOS session cannot be opened right now with this
slot. Most likely someone else (using a different CTC)
already has a session opened with this slot. Please try
again later.

EID-1022

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

480

Error Messages

Error Messages Reference

«
...
524
525
526
527
528
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: D-Link Страницы: 10

Бренд: D-Link Страницы: 29

DGS-3700 Series

Бренд: D-Link Страницы: 292

Бренд: D-Link Страницы: 140

DGS-1224T - Web Smart Switch

Бренд: D-Link Страницы: 61

DI-LB604 - Load Balancing Router

Бренд: D-Link Страницы: 14

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 45

Бренд: D-Link Страницы: 218

DES-3528 - xStack Switch - Stackable

Бренд: D-Link Страницы: 322

DIR-130 - Broadband VPN Router

Бренд: D-Link Страницы: 10

DIR-130 - Broadband VPN Router

Бренд: D-Link Страницы: 4

DIR-130 - Broadband VPN Router

Бренд: D-Link Страницы: 13

Бренд: D-Link Страницы: 13

DI-804HV - Express ENwork Router

Бренд: D-Link Страницы: 19

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды