Cisco NCS 2000 series Скачать руководство пользователя страница 247 | Manualshive

Страница: 247 / 602

background image

DETAILED STEPS

Step 1

In node view (single-shelf mode) or shelf view (multishelf mode), double-click the TXP_MR_10G, TXP_MR_10E,
TXP_MR_10E_C, TXP_MR_10E_L, TXP_MR_2.5G, TXPP_MR_2.5G, MXP_MR_10G, MXP_MR_10E, ADM-10G,
and OTU2_XP card.

Step 2

Click the

Provisioning

>

OTN

>

OTN Lines

tabs.

Step 3

In the FEC column, click

Enable

to activate the FEC feature. This causes a different OTN frame to be transmitted.

Alternately, in the E-FEC column (TXP_MR_10E and MXP_MR_10E), click Enable to activate the Enhanced FEC
feature.

Step 4

Verify that the far-end card is configured the same way by repeating

Step 1, on page 201

through

Step 3, on page 201

.

If the alarm does not get cleared, you need to report a Service-Affecting (SA) problem. Log into the Technical Support
Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or log into

http://www.cisco.com/c/

en/us/support/web/tsd-cisco-worldwide-contacts.html

to obtain a directory of toll-free Technical Support numbers for

your country.

FEED-MISMATCH

Default Severity: Major (MJ), Service Affecting (SA)

Logical Objects: EQPT

The Feed Mismatch alarm is raised when the mandatory power module input feed based on Power Supply
Unit (PSU) configuration is disconnected or incorrectly connected.

The alarm is cleared when the mandatory feed connection of power module is connected as per the PSU
configuration. To re-configure the feed connection, refer to

Power Redundancy

.

FEPRLF

Default Severity: Minor (MN), Non-Service-Affecting (NSA)

Logical Object: OCN

The Far-End Protection Line Failure alarm occurs when there was an

SF (TRUNK) , on page 390

condition

on the protect card APS channel coming into the node.

The FEPRLF alarm occurs on the NCS only when bidirectional protection is used on optical (traffic) cards
in a 1+1 protection group configuration.

Note

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

201

Alarm Troubleshooting

FEED-MISMATCH

«
...
245
246
247
248
249
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Cambium Networks Страницы: 68

Бренд: Cambium Networks Страницы: 110

Бренд: H3C Страницы: 33

S5500-SI Series

Бренд: H3C Страницы: 1217

Бренд: 3Com Страницы: 2443

Бренд: H3C Страницы: 3

Бренд: H3C Страницы: 4

Бренд: Ubee Страницы: 9

Бренд: Oracle Страницы: 112

Бренд: Fracarro Страницы: 12

MultiConnect SE MTS2EA

Бренд: Multitech Страницы: 2

SuperServer 5019S-L

Бренд: Supermicro Страницы: 61

Бренд: Time domain Страницы: 64

Бренд: Z Microsystems Страницы: 51

Бренд: Freund Страницы: 6

Бренд: AOpen Страницы: 18

BROADCAST POLLING FRAD BPF-14 BU

Бренд: DCB Страницы: 28

Бренд: ADIC Страницы: 140

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды